Gavatron
4th September 2009, 02:25 AM
Copied from Toymods
Have owned this for a while now, but it has been stashed at Takai's and then another mate's house until I had finished the Cressy and cleaned up the shed. So I present...
One cleaned shed with completed Cressy
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22209.jpg
Which allows for
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22210.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22211.jpg
And allows for progress.
Bits collected so far -
2JZGE
Front Sump
Autronic SMC
JZ -> W58 Bellhousing
Rebuild True-Trac Diff
Rust free hatch and bonnet
R32 GTR brakes
Update action
I bought a front sump a while back on ebay. While I was told it was complete, it wasn't. Came only with pressed tin bowl and allow piece. Ordered all the other bits new through work, including a nifty little block off plate for the oil level sender.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22212.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22213.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22214.jpg
Part numbers of the baffle, pickup, pickup gasket, block off plate and block off plate gasket.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22215.jpg
As it started this evening, with plenty of oil leaks.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22216.jpg
Hour or so later, minus air box, radiator, condensor and most A/C piping.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22217.jpg
Poo should be out by Saturday, ready for 2JZ fitments.
Also, if anybody sees a set of 16x8 or 16x9 SSR Meshies on as close to 0 offset as possible, give me a yell!
Takai said he could come round on Saturday to help me pull the engine.
I got bored after dinner, so a few beers and a couple of Megadeth CD's later...
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22218.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22219.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22220.jpg
W58 minus bellhousing
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22221.jpg
Height differences between the M and JZ bellhousings. This is because the JZ block comes out around the flywheel.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22222.jpg
JZ bellhousing installed
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22223.jpg
Busy today. Picked up:
5kg Cro-Mo Flywheel. No HD clutch kits available until June 16th due to a back order of clutch covers. Xtreme or Exedy as they both use the same supplier. So that's a bi shit.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22224.jpg
Ground Control coilover sleeve kit.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22225.jpg
Also grabbed some RA60 struts and power steering arms, and a set of GH Sigma LCA's. Stock MA61 LCA and steering arm on the bottom, Sigma LCA and RA60 PS arm on the top. Still need to get the PS arms reamed out to the right taper for the Sigma ball joint.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22226.jpg
Now minus front sus
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22227.jpg
Also grabbed my 2J from Takai.
Rear engined 2JZ Astina
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22228.jpg
Got it home and pulled the sump to swap it over, and the cam covers. Clean as a whistle inside. Big end and Main bearing are in new condition.
http://users.adam.com.au/djstew/Supra/16052009123.jpg
Sump should go in in the next couple of days. Need to order my shocks and cut down the struts to weld on the sleeve kit. Also waiting on a complete Super Pro bushing kit.
Not much time this weekend. Corporate box at the footy and a work do on Sunday.
Front sump all installed
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22230.jpg
Bonneville copy engine mounts installed. You can see 4 of the Yaris coils I'm using too. Built in ignitors.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22231.jpg
http://users.adam.com.au/djstew/Supra/23052009135.jpg
JZX81 Master Cylinder left over from a front cut bolted on. Stock one was leaking badly, as can be seen on the front of the booster. This one is 1" instead of 15/16". If it is no good it didn't cost me anything :P Lines need a little bit of tweaking.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22233.jpg
Just a little peek at the wheels I got from VA61DETT. Stock rear suspension with the arm jacked up to the bumpstop
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22234.jpg
And modded Sigma arms that Takai and I knocked up on the weekend
http://img192.imageshack.us/img192/6759/07062009150.jpg
No more rear suspension. Bushes are super flogged out.
http://img268.imageshack.us/img268/8088/11062009153.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22237.jpg
Minor update.
Dropped the tank this arvo to check inside and to do a fuel pump. Not too bad inside. Some scum. Best way to clean it out? Especially in the swirl pot?
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22238.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22239.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22240.jpg
Will be getting my new Autronic loom next weekend, and should have the throttle body plates here sometime this week to start making up the manifold. Brake rotors are in as well. 296x32 R32 GTR fronts and LS400/UZZ30 rears.
Have owned this for a while now, but it has been stashed at Takai's and then another mate's house until I had finished the Cressy and cleaned up the shed. So I present...
One cleaned shed with completed Cressy
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22209.jpg
Which allows for
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22210.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22211.jpg
And allows for progress.
Bits collected so far -
2JZGE
Front Sump
Autronic SMC
JZ -> W58 Bellhousing
Rebuild True-Trac Diff
Rust free hatch and bonnet
R32 GTR brakes
Update action
I bought a front sump a while back on ebay. While I was told it was complete, it wasn't. Came only with pressed tin bowl and allow piece. Ordered all the other bits new through work, including a nifty little block off plate for the oil level sender.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22212.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22213.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22214.jpg
Part numbers of the baffle, pickup, pickup gasket, block off plate and block off plate gasket.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22215.jpg
As it started this evening, with plenty of oil leaks.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22216.jpg
Hour or so later, minus air box, radiator, condensor and most A/C piping.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22217.jpg
Poo should be out by Saturday, ready for 2JZ fitments.
Also, if anybody sees a set of 16x8 or 16x9 SSR Meshies on as close to 0 offset as possible, give me a yell!
Takai said he could come round on Saturday to help me pull the engine.
I got bored after dinner, so a few beers and a couple of Megadeth CD's later...
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22218.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22219.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22220.jpg
W58 minus bellhousing
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22221.jpg
Height differences between the M and JZ bellhousings. This is because the JZ block comes out around the flywheel.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22222.jpg
JZ bellhousing installed
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22223.jpg
Busy today. Picked up:
5kg Cro-Mo Flywheel. No HD clutch kits available until June 16th due to a back order of clutch covers. Xtreme or Exedy as they both use the same supplier. So that's a bi shit.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22224.jpg
Ground Control coilover sleeve kit.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22225.jpg
Also grabbed some RA60 struts and power steering arms, and a set of GH Sigma LCA's. Stock MA61 LCA and steering arm on the bottom, Sigma LCA and RA60 PS arm on the top. Still need to get the PS arms reamed out to the right taper for the Sigma ball joint.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22226.jpg
Now minus front sus
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22227.jpg
Also grabbed my 2J from Takai.
Rear engined 2JZ Astina
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22228.jpg
Got it home and pulled the sump to swap it over, and the cam covers. Clean as a whistle inside. Big end and Main bearing are in new condition.
http://users.adam.com.au/djstew/Supra/16052009123.jpg
Sump should go in in the next couple of days. Need to order my shocks and cut down the struts to weld on the sleeve kit. Also waiting on a complete Super Pro bushing kit.
Not much time this weekend. Corporate box at the footy and a work do on Sunday.
Front sump all installed
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22230.jpg
Bonneville copy engine mounts installed. You can see 4 of the Yaris coils I'm using too. Built in ignitors.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22231.jpg
http://users.adam.com.au/djstew/Supra/23052009135.jpg
JZX81 Master Cylinder left over from a front cut bolted on. Stock one was leaking badly, as can be seen on the front of the booster. This one is 1" instead of 15/16". If it is no good it didn't cost me anything :P Lines need a little bit of tweaking.
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22233.jpg
Just a little peek at the wheels I got from VA61DETT. Stock rear suspension with the arm jacked up to the bumpstop
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22234.jpg
And modded Sigma arms that Takai and I knocked up on the weekend
http://img192.imageshack.us/img192/6759/07062009150.jpg
No more rear suspension. Bushes are super flogged out.
http://img268.imageshack.us/img268/8088/11062009153.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22237.jpg
Minor update.
Dropped the tank this arvo to check inside and to do a fuel pump. Not too bad inside. Some scum. Best way to clean it out? Especially in the swirl pot?
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22238.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22239.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/7/22240.jpg
Will be getting my new Autronic loom next weekend, and should have the throttle body plates here sometime this week to start making up the manifold. Brake rotors are in as well. 296x32 R32 GTR fronts and LS400/UZZ30 rears.