4agze ke70

[AmyC]

hey people

Some of you know me as too_quick from rolla club, If you dont know me im very slowly building(and i mean slow)a 4agze powered ke70.

Now onto the good stuff.

So far i have pulled the engine out of the halfcut, removed back seats from the ke70.removed some rust got more to go, Put autotecnica seats in as well as autometer boost gauge and stewart warner ultra shift light and my oba steering wheel. http://www.ae86drivingclub.com.au/forums/emoticons/tup.gif

I have a ae92 4agze, Afm, Dli etc. This is my halfcut the day i got it.
[attachment=6892:attachment][attachment=6893:attachment]

This is it at the moment with a lot of help from Medicine_man and Teddy.
[attachment=6894:attachment]

This is my ke70.Mmmmmmmmmm yellow. Notice the MS paint lowering job its fully professional. http://www.ae86drivingclub.com.au/forums/emoticons/laugh.gif
[attachment=6895:attachment][attachment=6896:attachment]

The inside and some parts ive attached.
[attachment=6897:attachment][attachment=6898:attachment]
[attachment=6899:attachment]

[MARKE70]

Lookin tops man.

you planin to drift the old girl????

GZE FTW!

[AmyC]

hey hey

Its mainly getting built to compete in autocross but its going to get a flogin around the local dirt roads in beaudesert. http://www.ae86drivingclub.com.au/forums/emoticons/tup.gif

[AmyC]

We pulled the 4k and the trimatic out lastnight.a big thanks to medicine_man and teddy for doing most of the work again. http://www.ae86drivingclub.com.au/forums/emoticons/2thumbs.gif

[AmyC]

here is some photo's take from lastnight. http://www.ae86drivingclub.com.au/forums/emoticons/2thumbs.gif
[attachment=6993:attachment][attachment=6994:attachment]

[AmyC]

Its been a while since my last update so here is the recent news.


- the ae71 crossmember is in.
- 4k is in pieces for people to take FREE parts if needed.
- cleaned the engine bay today.
- im working on getting a jdm t50 now.(I know its risky using a t50 but i can learn to stop 6k clutch dumps)
[attachment=7570:attachment][attachment=7571:attachment]

[AmyC]

mmmmm twinlights.
Not finished yet but still looks hot.
[attachment=7998:attachment]

[green_boy_91]

looking good man hope it goes well for ya,
lights look good http://www.ae86drivingclub.com.au/forums/emoticons/smile.gif

[AmyC]

The lights are proving to be more of a bitch than i expected.

[Andrew]

Yeah, doing that on a mates KE also...no idea how to wire up those high beams.

[AmyC]

Im haveing mine as all low beam and high beam instead of 2 being low and high have them all low and high.

[AmyC]

TA22 light didnt work out but i bought a AE71 wagon for all its goodies.

[attachment=9318:attachment]

[MountainRunner]

OH very nice same engine im looking to put in my ke70 just dont no how much and were http://www.ae86drivingclub.com.au/forums/emoticons/sad.gif

[ke70dave]

how come the lighs didnt turn out good?

im putting xt118 corona ones (pretty simliar to ta22) in my ke tomorow....doesnt look hard to do, just gota weld some bits here and there, what dramas did you run into?

[AmyC]

I suck at welding and fab so yeah.

Im fully spripping down the AE71 for parts and spare parts coz i know im gona hit something on the track. I wont be needing the rwd 4ac so as soon as the gze is mounted in the KE70 i will sell it.

The KE70 will getting worked on alot now that i have the parts and what not. http://www.ae86drivingclub.com.au/forums/emoticons/smile.gif

[AmyC]

Hahahahahaha my dog likes the back of the wagon.

[attachment=9351:attachment]

[AmyC]

The 4ac and t50 are out of the ae71.

Got me a 20v flywheel.

Getting my RPM heavy duty clutch soon when repco can get it in BAH!

[AmyC]

pulled out the ae71 pedal box, and bought a seal kit for clutch slave and master.

[attachment=9686:attachment][attachment=9687:attachment]

[AmyC]

Diff and crossmember are coming out tomorrow.

[Gilly]

brings back fond memories of ripping out an ae71 pedal box at the wreckers like 20 minutes before they closed as i knew of a dude coming the next morning to pull it out.

i destroyed the cluster, dash pad nad pretty much every plastic trim in that area. pick apart FTW!!

[driftke70]

i would of put the ke front on the ae wagon and 4agz'd that shiz, but it looks like a sweet project.

[AmyC]

Diff is out, crossmember is out.

The ae71 wagon has to much rust in it and it has leaf rear end and id rather coil over setup.

[attachment=9756:attachment][attachment=9757:attachment]
[attachment=9758:attachment]

[Stuck]

YOU KILLED ITT * cries * ^

[AmyC]

YOU KILLED ITT * cries * ^[/b]
Yes i killed it but its giving my KE70 a new life so its worth it, Plus early KE70's look better. http://www.ae86drivingclub.com.au/forums/emoticons/wink.gif

I got the pedal box out of the KE70 yesterday aswell.

[AmyC]

Got me a exedy clutch and the motor will be in this week.

[AmyC]

Flywheel on and clutch on, fitting gear box tomorrow and removing broken engine mount bolt.

[AmyC]

Gearbox on, 1 engine mount on, fitting other tomorrow and then maybe the engine FUCK yeah.

[AmyC]

Engine in, T-50 in and now i need to cut up the SC outlet to let the intake pipe face the front of the engine and not the fire wall.

[attachment=10250:attachment]

[AmyC]

Havent done alot lately thanks to christmas but i have actually done something lately.

Cut the holes for the pedalbox and installed pedalbox and reassembled the dash properly, It took me about 5 - 6 hours to cut the holes and put eveything back together. I found a grinding bit that goes onto a drill, I asked the old man how much was it $60, A bit expencive but dam it does a good job made me look pro. Glad thats out of the way now.

thanks to 86sp for the stainless steel intercooler piping and a modified supercharger outlet. The SC outlet is a bit rough so I'm going to take it to a mates place to clean it up and make it flow a bit better.

The SC outlet looks better than in the photo its just a bit rough inside.

[attachment=10964:attachment]
[attachment=10965:attachment]

[driftke70]

looks like its coming along nicely, should be shmokin in no time

[AmyC]

Going to start the wiring very soon which will be fun http://www.ae86drivingclub.com.au/forums/emoticons/dry.gif

Just need the wiring and intercooler piping down and out of the way and then all the little fiddley bits come up.

[AmyC]

Well i started the wiring yesterday and i have bit off more than i can chew so i have inlisted a buddy to help me out soon. http://www.ae86drivingclub.com.au/forums/emoticons/wink.gif

[Bustin_86]

Look at the camber on that ae71 wagon!!!LOL!!!

[AmyC]

Look at the camber on that ae71 wagon!!!LOL!!![/b]
Its not excesive at all http://www.ae86drivingclub.com.au/forums/emoticons/crazy.gif . I did a bit more of the wiring today and ive nealy got it cranking over so http://www.ae86drivingclub.com.au/forums/emoticons/greenbounce.gif

[Bustin_86]

Well done man, feels great when you actually accomplish something aye http://www.ae86drivingclub.com.au/forums/emoticons/tongue.gif

[AmyC]

Im goig to leave the wiring for now and get the FMIC piping and fuel setup done, Injectors are getting flow tested soon and new O rings.

[AmyC]

Got some extractors from option1garage on saterday and i most likely will get them to finish off the wiring and ic piping and a few little bits.

[Rakurai]

Dude i swear on rolla club... it says ur car has 300kw.. i lold... coming along nicely

[AmyC]

Haha yeah it had 318rwkw i think, Got some 15's for it today so i will post a pic once they have gotten a respray.

[AmyC]

These are tear drop s13 silvia rims 15x6, I think they look ok but im going to respray them.

[attachment=11354:attachment]
[attachment=11355:attachment]

[kewagon]

they look sleeper style man, what colour ya gunna paint em??? would look good in a darker colour

[kewagon]

they look sleeper style man, what colour ya gunna paint em??? would look good in a darker colour

[AmyC]

Sleepers styles own, I might leave them silver actually, The colour is really growing on me.

[Brendo]

silvia wheels? arent u gonna put some nice dishies on it.... it deserves them

[4awagon]

they look good, i just got a set of the 180sx wheels for my wagon hope they suit my car like them ones suit yours. http://www.ae86drivingclub.com.au/forums/emoticons/tup.gif

[AmyC]

silvia wheels? arent u gonna put some nice dishies on it.... it deserves them[/b]
Bah i dont see the point in dished wheels apart from looks http://www.ae86drivingclub.com.au/forums/emoticons/blink.gif S13 ca18 silvia rims.

4awagon they should fit the rear of your car but they will most likely touch your front struts unless your running adjustable coilovers, some thick spacers will stop it touching aswell.

[Andrew]

They look tough painted black and about 3 inches lower.

[AmyC]

Front end lowing comes next with adjustable coilovers mmmmmmm. Undecided what i want to do with the rear end suspension wise so im open to suggestions but remember im not a drifter.

[4awagon]

im no drifter either, i might put long studs in the front and run 10 mm spacers

[AmyC]

I need about a 1 inch spacer to fit s13 rims on the front of mine.

[Gilly]

if you haven't already got your coilovers use the S13 stuff, it will make the wheels fit and not look as ghey as the wheels won't sit as far in the guards. rear end if you are non driftable type something like a low king spring or lovels spring or something like that, or something stiffer again if you are using it for motorsport orientated purposes. i can't think of anything in between generic style kings and cut falcons rate wise. miht have to get some 4.5kg/mm AJPS ones.

[AmyC]

Allready have the coilovers.
I need to get another set of springs though, 8kg springs a just too stiff for what i want.

Im willing to swap my Eibach 8kg springs for something a little softer.

[AmyC]

Pick up my razorback this sunday.

[AmyC]

IT HAS ARRIVED. http://www.ae86drivingclub.com.au/forums/emoticons/biggrin.gif

[attachment=12075:attachment]

[AmyC]

Getting some rims soon aswell.

[foxtail]

I was denied www.razorbackecu.com.au, so its www.razorbackecu.com now http://www.ae86drivingclub.com.au/forums/emoticons/smile.gif

Is this Andy's old ecu?

[AmyC]

I think it was, Matt bought it from Andy i think and didnt use it so bought it and i have a loom too which i dont need and im not sure if its from a 16v or a 20v ?

I will get some pics.

[AmyC]

[attachment=12116:attachment]

[AmyC]

[attachment=12180:attachment]
[attachment=12181:attachment]

[hilton]

sleeeeeeeeppperrrrrr!!!!!!!! http://www.ae86drivingclub.com.au/forums/emoticons/smile.gif

[anastasios]

i rekon leave the 8kg springs in there and use ford rear springs

[AmyC]

i rekon leave the 8kg springs in there and use ford rear springs[/b]
Nah the whole coilover kit has been sold off as i dont need them now.

[AmyC]

Ic piping done and done.

[attachment=12233:attachment]

[Andrew]

You have no idea what you've started giving Matt that BMX.

The day after he got it, just rode around everywhere, got mega sunburnt has been too scared to get back on it. He's the BMXican.

You get that mess of a razorback untangled?

[driftke70]

lookin good,

cut that excess thread off on those hose clamps, to tidy her up,

this things going to be bit of a weapon.

[AmyC]

You have no idea what you've started giving Matt that BMX.

The day after he got it, just rode around everywhere, got mega sunburnt has been too scared to get back on it. He's the BMXican.

You get that mess of a razorback untangled?[/b]
That loom is way to complecated for me so i will leave that for Sam to check out.


lookin good,

cut that excess thread off on those hose clamps, to tidy her up,

this things going to be bit of a weapon.[/b]
Yeah i might get around to that soon, Just need to get the cooling system done quick.

[foxtail]

Dude, I need a AE71 wagon diff, and some stock AE92 struts, I will give you a discount on the wiring job.

[AmyC]

Dude, I need a AE71 wagon diff, and some stock AE92 struts, I will give you a discount on the wiring job.[/b]
Fuck yes, I will hold it for ya http://www.ae86drivingclub.com.au/forums/emoticons/wink.gif

[AmyC]

Wiring should be getting done this weekend so no more putting it off to spend the money on other cars http://www.ae86drivingclub.com.au/forums/emoticons/biggrin.gif

Bought a Ae71 csx sedan too so that will be my daily when i get my licence back.

[AmyC]

Ae71 csx has been sold pending payment and pickup, With the money i will be buying fuel pumps and replacing timing belt and oil, filters and shit.

I swapped dash's from the clock to a tacho dash aswell and have neally completed the cooling system.

[AmyC]

Spent a few hours today finishing the cooling system and cleaning up the water pumps etc, I'm also halfway through changing the timing belt and it still had the genuine Toyota belt in place but in great condition Exclamation .

Timing belt will be done on monday, Wiring and Razorback installation on Sunday, Radiator andf thermo fan mounted tomorrow.

Gilly spec PANDA EYE'S

http://www.ae86drivingclub.com.au/dcimages/4/8/4/3/133471.jpg

http://www.ae86drivingclub.com.au/dcimages/4/8/4/3/133472.jpg

[4awagon]

looking good http://www.ae86drivingclub.com.au/forums/emoticons/tup.gif

[AmyC]

I think im up for a left hand side cam seal too http://www.ae86drivingclub.com.au/forums/emoticons/angry.gif

[driftke70]

that picture at the top just gives me shivers, wiring, a ke builders mortal enemy

[AmyC]

Wiring OMFG i hate it so i called Sam and he is doing it for me and he comes packing daewoo coils http://www.ae86drivingclub.com.au/forums/emoticons/tongue.gif

[AmyC]

Wiring and razorback is 90% in, Cam seals replaced, Timing belt replaced.

Fuel pumps purchased and 4 point harness has arrived too.

[attachment=13016:attachment]

[AmyC]

[attachment=13119:attachment]
[attachment=13120:attachment]

[AmyC]

[attachment=13218:attachment]
[attachment=13219:attachment]

[AmyC]

[attachment=13660:attachment]

[AmyC]

[attachment=13699:attachment]
[attachment=13700:attachment]
[attachment=13701:attachment]

[AmyC]

[attachment=14073:attachment]

[dr1ft-pig]

looking good man.... will be good to see it on the road... how long r we looking at till we see it on the tar??

[AmyC]

Not to long now that i have a full time job.

[Gilly]

coming along nicely

the world needs more boosted KE's http://www.ae86drivingclub.com.au/forums/emoticons/tongue.gif

[hilton]

get some smaller tyres,,instead of them tractor ones lol, and drop it like its hot..will look way good

[hilton]

just an oober quick chop

[MountainRunner]

^^+ camber http://www.ae86drivingclub.com.au/forums/emoticons/laugh.gif

[hilton]

lol better?

[MountainRunner]

better it looks like caek

[AmyC]

The time will come for Suspension components to be installed, They are being collected as we speak.

http://www.ae86drivingclub.com.au/forums/emoticons/wink.gif

[dr1ft-pig]

just been reading through this and have realised many people have xe7x's in their signatures that were made in that link posted the other night lol

cars looking good man

[MARKE70]

car is looking great man, You wont be dissapointed with that motor, they have balls-i like balls

allso - i bought some wheels from wreckers and they had those Classic 65 tyres on them and they were SO good to slide on. i did 2 track days on one set and they were really grippy

[AmyC]

One of the classic 65 tires has 2 gashes in it so SKID TIRES definatly.

[MARKE70]

mine did too wow

this could be a good omen or watever those things are called.

Both GZE ketos, Both got yucky big tyres that are actually turn out to be awesome drift tyres, and the both had gashes, mmmmmmmmmm some freaky shit there i say lol

[hilton]

y dotn youz hurry up an dget married lol jks,,,,,nah mark's owns urs des. lol

[AmyC]

Haha why dont you buy a Dictionary, You know why i have been quiet lately its coz im hording engine "parts" but you will find out sooner or later what they are.

Of coarse marks is better, His runs!!!!!!!

[lewa]

nah his is better cos his doesn't belong to you http://www.ae86drivingclub.com.au/forums/emoticons/tongue.gif hahaha just kidding des-dog now hurry up and finish it!

[AmyC]

turbo???? please[/b]
Not giving any details as of yet, People will see it when its ready to run.

[kewagon]

turbo???? please