PDA

View Full Version : Betty Crocker



lolwat
2nd October 2012, 09:47 PM
Racecar is race
Thought i would make another Build thread
Chances are the more you dont like something, the more i will like it, so say as you please

Racing red KE70, with Racing matte black bonnet(hate it), metallic grey engine bay

Engine:
G4JP 2.0 N/A
ARP head studs
Cometic head gasket
R155
AE86 rad
intercooler undecided
Td06 20g with a T3 flange(not a definite yet)

Fuel:
RCI Race cell
bosch 044 (possibly 2)
2L surge tank
yet to decide on lift pump
all to be mounted on ALU frame mounted in between the rails where the boot floor was
all new E85 compatable lines to be run all with speedflow/aeroflow/proflow fittings

Front:
RX7 Front brakes
AE86 front struts, cut and shut coilovers (in J lands) Probs go BC's or if i can get coin together Shockworks
8 KG springs
TRD (tokico's) blues
2x 20 cent peice in the bottom
Top Secret top plates
T3 steering arms(going to see how they go might go back to cut and shut 86 items)
RA60 rack ends
T3 tierods
Magic Man Lower control arms
Magic Man Caster rods and brackets
Ke70 rack
AJPS lock spacer
Cut up seam welded KE70 X member (possibly moving rack forward as well)

Rear:
210mm 6kg AJPS springs, with 1 1/2 coils cut
Peddars GSR short stroke shocks (keep springs captive)
Shortened G-series, adjustable panhard mount
JDM 86 disc's and calipers
Commo Panhard , cut and shut with adjuster
Axle snappers
Equal Length 4 Link

Interior:
Stripped
Swift GTI passenger seat
Nardi (old school)
D1 quick release
Gutted Dash with evo 7 cluster
Power switch in cab
Cool V-TEC YO drawings on the roof
Battery to be mounted in boot again or on tunnel


Exterior:
GHETTO
JDM 86 RIMZZZZZZZ
Other pair unknown simular offset to JDM 86 rims
rears rolled with a wood leg from a chair
Fronts, pliers and Jack Handle
No rear bumper
Covered in shit(you dont wash whores)
ae71 mirrors and Front windows


pictures, everyone likes pictures
OLD BAY
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/181584.jpg
Then one night, making a personal best (11 mins from cricket field heading out of Glossodia(near turf farms) to Crimebrook), it stopped as i pulled into my street

Then slapps 4a
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/402842.jpg
as it sits at the moment, with slappa 4a squirting(oil) more then clays mum
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/402844.jpg
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/402846.jpg

i got lazy JDM pointz will be calculated at a later date

blake.
2nd October 2012, 10:20 PM
You forgot to mention the third strike sticker (+5 points)

lolwat
2nd October 2012, 10:35 PM
will calculate tomoz hahahaha

lolwat
8th October 2012, 11:21 PM
This is going into factory this weekend, I am still looking for a decent K's 4g63, triton g box is sitting at MEEK, Mate (from MEEK) has a loom, ecu, Cams, got a LSD centre for G series(standard out of hilux) so if i cant tighten it to the shit house ill weld it, or sort something else out

blake.
9th October 2012, 06:13 AM
Don't forget about the ems I got here,

lolwat
9th October 2012, 01:28 PM
i genuinly forgot, i have to come and get it off you, do you need anything 4a wise??? selling it all soon, going back to ke x member too

ke_70
10th October 2012, 10:13 AM
you win the lottery or somthing?

lolwat
12th October 2012, 06:11 PM
you win the lottery or somthing?

pay went up(not that much) i have the room to do it, and i dont do anything, apart from gear, food and car parts there's nothing else to buy, for what i have sold the running gear from this for, i have bought an engine, 044, intercooler, G series, pending matts reply another 044 and RCI Fuel cell, I have more then enough people/Friends to help, other mechanics, general smart ####s, body builders, Metal fab guys, spray painters, i have no reason to fail

Plus i have to keep up with blake when he goes SRDET

lolwat
15th October 2012, 10:39 PM
In factory, diff out, rest of parts should be out tomoz, then waiting on chassis table (chev cab on it), pick up engine this weekend

GOT-20V
16th October 2012, 01:46 AM
Gear as in roids?

lolwat
16th October 2012, 01:26 PM
Gear as in roids?

nah not that shit, im a fat ####

Low Style
16th October 2012, 04:30 PM
Gear?

lolwat
17th October 2012, 10:01 PM
Shortened G series Paid for, another 044 and RCI fuel cell paid for

lolwat
21st October 2012, 12:02 AM
Did some work, after work today
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/404409.jpg
Nek minit
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/404411.jpg

blake.
21st October 2012, 08:35 AM
Dat tomahawk.

lolwat
21st October 2012, 09:01 AM
its awesome, didnt know how it got there, then ben said he found it in my guard HAHAHAH

lolwat
21st October 2012, 09:02 AM
off to Rhys's then matts for hektic parts

ke_70
24th October 2012, 09:26 PM
even more hektic that a tomahawk?

lolwat
24th October 2012, 09:42 PM
RCI Race cell, Some random big pump(probs sell it on), Magic man G series, started marking out top boxs last night, fucking rat shit tonight

drift kid
26th October 2012, 05:51 AM
get the engine!!11!!1!!!!!1!!!!

lolwat
26th October 2012, 09:50 PM
going with little mike this sunday to get it

lolwat
7th November 2012, 10:12 PM
pics will be soon
Got engine
started making frame for fuel cell
Magic man Lower control arms and caster rods
Dash has been gutted completely

drift kid
4th December 2012, 05:10 PM
just because this peasant never updates, I made the rear equal length trailing arm boxes and we cleaned out the back of the ke plus marked it all out ready for cutting, 40*+ temps slowed the progress stupid fast lol
http://www.ae86drivingclub.com.au/dcimages/1/8/0/409311.jpg
http://www.ae86drivingclub.com.au/dcimages/1/8/0/409313.jpg

lolwat
9th December 2012, 12:29 AM
bam!
http://www.ae86drivingclub.com.au/dcimages/502417.jpg

lappy
11th December 2012, 12:40 AM
Good work! What is the thickness of the steel you used for the box sections? I'm planning to to the same

Sprinter Freak
11th December 2012, 09:36 PM
box sections are looking good man. needs more tubs all round tho :cool:

lolwat
12th December 2012, 08:07 AM
2mm plate, i believe
got to clean up underneath as benny smashed the other box (:cool:) last night, looks fuckin awesome, just rear tunnel area to do now, need to shorten panhard rod mount on my diff as its made for watts link, add a bar so i can have 2-3 panhard bar mounts/levels(if clay comments saying half assing not going watts link, ill bite your face off), weld on spring perches, powder coat, get new crown and pinion setup and thats diff done
chiseling sound deadner out, isnt as mad as people make it out to be, do a little bit in between things its not too bad

fronts yes rears no :)

lolwat
22nd December 2012, 07:25 PM
both rear boxes are done, rear tunnel is done, now have a diff center that has been welded to the fucking shit house, cut off watts link mount and shortened the other one, ready to weld on 10mm stainless plate so i can have panhard at different heights, spring perches have been welded on, so diff is nearly done ready for sandblast and powder coating

bought a 3m speedglass 100 series helmet, so i can get cracking on welder as there wasn't one at my factory
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/502902.jpg

Gunner
22nd December 2012, 07:54 PM
i think you ####s need to start working on the ej86. seriously good effort dude get more pics up you slut

lolwat
22nd December 2012, 08:09 PM
Benny has pumped work, ive been a bit lazy, did a bit on the welder today, pretty happy wth my self(jumped in the deep end a bit welded spring perches on), so ill get smashing every seam with wire wheel, and seam welding it all

once diff is in(rolling again) going to flat tow/push, it around to bennys work, so he can make a lovely alum frame and jacking point in the back, then i can start fuel setup, waiting on invoice from bills auto fab as well so i can pay the mofo hahahah


hurry up #### hahahahah, ill beat you :P

Gunner
22nd December 2012, 08:44 PM
i dont give fuck if you do lol afterall i believe that, those 4 link boxes were cut from my templates... oh and isnt that my doff.... wait a sec, who told you how easy this conversion can be... yeah thought so you little shit :D

lolwat
22nd December 2012, 09:01 PM
templates yes, diff i cut up :P, it was my idea you just agreed HAHHAHA

:) finish yours whore
ill get pics when i think to take a camera to factory

drift kid
26th December 2012, 05:48 PM
Haha every photo so far was taken by me and you forgot to mention that I finished you diff tunnell ;)

lolwat
26th December 2012, 10:48 PM
i did post before pic

drift kid
27th December 2012, 04:06 PM
Yeah which i took and you stole from my Facebook lol, get back into the car now

ke_70
27th December 2012, 05:09 PM
nice progress happening here!

boxes look real good, much better having adjustment in there.

did you make the box channels yourself? this is the next thing i need to do on my car.

keen to see the adjustable panhard mounts also, i'm halfway through making one at work.

drift kid
30th December 2012, 09:24 PM
The template for the boxes came from gunner but i fabricated it all up

lolwat
31st December 2012, 02:42 AM
I wont have adjustment on the body side for panhard just diff side

yea factory got a mad tidy up LOL

Still sorting out Bell housing from Bills auto fab in the US, once thats paid im broke for a week or 2 till i go back to work

Gunner
31st December 2012, 07:46 AM
see about the ej bell for me dickface

lolwat
31st December 2012, 12:05 PM
bellhousing sorted, nearly 100 more but owells

updated first post and should probs blur my plates too benny, plan to keep rego

lolwat
23rd January 2013, 11:57 PM
starting to push the whole rego thing
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/503979.jpg

lolwat
5th February 2013, 11:32 PM
Diff's getting powder coated
and
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/504652.jpg

Rack now sits right up against Xmember, boxed in with 3mm plate

lolwat
9th February 2013, 01:54 PM
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/522648.jpg
hold it out to fit hoist

Sprinter Freak
9th February 2013, 06:09 PM
you end you getting that panhard rod off the diff?

lolwat
10th February 2013, 09:45 PM
nah we packed up and went home, was stuffed
ill try tomoz night, pending how putting the other hoist goes

lolwat
12th February 2013, 11:03 PM
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/538484.jpg
Now to wait for it to come from the US
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/504980.jpg
pretty good for how cheap it was, need to be cut up though hahahaha

also, will be running an EVO7 ECU, engine loom, Cluster, fan controls, launch control, may even duel map, doubt it will ever go on 98 though

stixy
15th February 2013, 01:49 AM
Wow mate nice work!!!

Subscribing

lolwat
15th February 2013, 06:35 PM
Cheers

http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/505091.jpg

diffs back from being powder coated satin black looks mint

lolwat
26th February 2013, 09:24 PM
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/522653.jpg

Now to fuck my tunnel off

lolwat
3rd March 2013, 12:48 PM
Pending price my boss comes up with (doubt it will be cheap enough) or from Yahoo Japan, i will Getting Evo7 cluster, and basically a front cut loom, to run everything thing off a evo 7 ecu (fans, boost, temps etcetc), will look into what would have to be done to convert the hilux box speedo sender to work with the evo 7 cluster and ECU, as i will be running launch control etcetc(under 5km's it will use launch control)

shifter position doesnt look to bad with the R155 and the 4g, considering how far back i sit anyways it should be sweet, went to sit box and engine in thurs night, and couldnt find an angle grinder(noramlly everywhere)

lolwat
14th March 2013, 11:13 PM
awkward moment whne your inpout shaft is 25mm too short

Jacobxxx
17th March 2013, 09:47 PM
Clays mum gets that issue with the young ones

Matt
18th March 2013, 11:57 AM
Clays mum gets that issue with the young ones

it sucks being young hey jacob...


This build is Looking good!

Jacobxxx
18th March 2013, 12:36 PM
She gave me a sticker for trying

lolwat
20th March 2013, 11:08 PM
currently in i hate this POS mode, Need to get some monies up and get a R154, might be going evo 5 cluster, due to buying rolling shell, mate needs rear end for GSR i need a WHOLE front loom, end up pretty cheap

lolwat
29th April 2013, 11:09 PM
Whole evo cluster can eat a penis, too much work for little/no return
may do it at a later date

R155 input shaft is going to be cut and shut to match a R154 item
Broke as fuck, how it sits at the moment
http://www.ae86drivingclub.com.au/dcimages/3/7/5/4/507440.jpg (http://s302.photobucket.com/user/chop92per/media/420730_10200142204851854_1288609257_n_zps1b021bbe. jpg.html)

joeschmo_57
30th April 2013, 01:53 PM
Put 4G in that clean looking kombi

Filth70
30th April 2013, 07:54 PM
Hey man looking good, Do you have any ideas how you are going to do your front. I am just about to start mine interested to see what other guys are doing.

lolwat
28th May 2013, 10:11 PM
Tube rad support, all removable, for easy engine removal
engine sits nicely, box fits in tunnel and shifter comes out in standard spot, just to make mounts up

drift kid
18th July 2013, 11:15 AM
Got my bender all setup now so more regular updates will be here soon, cage/radsupport/curlytubethings will be done soon

drift kid
24th July 2013, 10:06 PM
Finally had some work done to this hunka yesterday, I stripped a heap load more sound deadening out and mick and myself cleaned and (properly) seam welded the whole bay, getting ready for motor mounts and tube work.