Jacks rebuilt drift e7

[jackthecat]

so were to start. i got this ke70 for straight swaps for my fully sick minitruck.... (it was not full sick)
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505646.jpg

that is the 1st day i got the car
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505647.jpg

so is this one

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505648.jpg
fit a ae86 notchback boot lip, don't worry the mounts were all stuffed so didnt wreck it.

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505649.jpg
how the motor looked when i got it, talk about proplems on how it was put together. the manifold had 3 of the 9 bolts holding it on.


so once i had realised how much was done wrong in the car i made my mind up i was goin to strip the whole car and fix it all.


started with a new bigport head that came with the car
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505650.jpg

then it was time to try get it running, spend about 6 weeks tracing wires back and going over stuff fixed up a couple little things and the timing was 180 out then it fired up but the day before the timing was out enough to make some good flames got a photo
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505651.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505652.jpg

then it was onto the brakes, as i wanted to run 86 p/s knuckles for lock i had to ditch the xt130 struts, Peugeot 300mm discs and 75 series landcruiser calipers and went to adm ae86 struts hubs and calipers with rta vented slotted dimpled disks. shortened the strut by 60mm for the kyb agx inserts i used mr2 ones (will get code later) and then welded on sleeves ( you can use adm calipers with qfm pads 3mm less a pad so u can run the jdm disks)
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505653.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505654.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505655.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505656.jpg

then it was time to start hiding the loom as it looked like a brothel that took maybe a good days work and some other parts i had picked up from craig at just jdm imports. ended up lookin like this

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505657.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505658.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505659.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505660.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505661.jpg


then the oil cooler and new clutch line came earls fittings are not cheap!
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505662.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505663.jpg


then came the hoshinos which later got swaped for some volk mesh and t18 bars

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505664.jpg

when i 1st got the car i striped the whole inside (wish i didnt now) and chucked it in the bin. then got some fake brides (now for sale for something i fit into in 6.4")so now makin a roof lining with book contact (love lighting mcqueen) lol

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505665.jpg

heres a photo of my lock and star indorcators i got from yahoo JP through jesse streeter.

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505666.jpg

then a mate was sellin his smallport with hks cam gears toda flywheel with trd 3 puck clutch toda r 272 with 7.9mm lift ex and 288 with 8.5 lift in at the right price so now the bigport is all unbolted and ready to come out and smallport t3 manifold bought for the itbs will be building a 7a block for this head soon/ once im bored of the 4a also have a trd 2 lsd on the boat from japan through jesse streeter with a 4.3 but i have a 4.6 cw/p at already so will be taking my diff to top cog at the sunny coast to get it full rebuild and the 4.6 put on.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505667.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505668.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505669.jpg


then a mate offered to straight swap wheels with me for my 14x7+7 hoshinos for his 14x8.5-17 and 14x8-10 volk mesh
heres a photo of the guards pumped and it still couldnt roll.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505670.jpg


so then i got out my good friend mr grinder. have left it so i can weld on front guards later but for now as i had them old school bolt on ke70 flairs till they break.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505671.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505672.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505673.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505674.jpg

and now how the car sits as of tonight.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505675.jpg


engine - JDM small port full RWD set up w/toda 288/272, old school hks cam gears metal head gasket, maybe some other mystery internal mods. ports look stock. billet flywheel and 3 puck. bought as a package from a mate (SLYDAR) that got it from Craig at Just JDM Imports. hopefully be in by the end off the weekend got to be in before the 22/3 getin a shoulder reconstruction then and can use my right arm for like 3 months

management - Haltech e8

exhaust - full bolt on RSR with cat, single rear muffler with silencer installed (60mm) 4-1 mild steel jap header.

footwork - I built coil overs learnt by watch my friend Dimitri (SLYDAR) build his own brand of Custom Compact coilovershttp://www.ae86drivingclub.com.au/forums/images/smilies/smile.png otomoto kit with 8k springs and kyb agx mr2 dampener. PS knuckles, AJPS 40mm rca, AJPS extra lock rack ends, what i suspect is tein camber tops, cusco tower brace. a few newish 2nd hand poly bushes. rear has ghetto cutties and suzuki shocks. soon to be mcn rear coilovers, ra65 celica front swaybar rear i think is just stock and a whiteline panhard rod

diff - t18 s1 with swaybar mounts welded on with 3.7 welded atm but have 4.6 cw/p already in my room and have a trd 2way lsd on the boat from japan will be getin 4.6 in it and set up by duncan at TOP COG

interior -striped with no seat atm tryin to sell copy fixed back bride glitter backs 750ono with a lighting mcqueen roof lining and 15" glitter red mooneyes wheel

aero - volvo cut down 240 front lip will post photos soon of it on the car and rear bolt on flairs

wheels - widened 14x8-10 volk mesh on the front, widened 14x8.5-17 volk mesh on the rear. hero hz-1 tires 185 55 14.

brakes - JDM rda vented slotted dimpled discs with ADM calipers using QFM A1RM pads (-6mm friction material) also had to grind the top corners out of the caliper brackets (like 2mm) still safe. rear stock drums.

[Mika]

Looking rad dude! Keen to see this progress!

[Sprinter Freak]

This is awesome man! Digging the quad light and the meshies.

[jackthecat]

Looking rad dude! Keen to see this progress!
sadly wont be much goin on with working on the car as just found out to day i need a shoulder reconstruction which is happing in 2 weeks, but will be buyin lots of the parts to finish it so once im beter i can drive it. all there is really is rear coilovers mcn ones, tune once smallport is in with quads and cams and new velo podium II XL seats x2 and mod plates

[Mika]

sadly wont be much goin on with working on the car as just found out to day i need a shoulder reconstruction which is happing in 2 weeks, but will be buyin lots of the parts to finish it so once im beter i can drive it. all there is really is rear coilovers mcn ones, tune once smallport is in with quads and cams and new velo podium II XL seats x2 and mod plates

Sorry to hear mate, hope it all goes well and your recovery is a fast one! Look forward to seeing you post up all the goodies your going to get for it.

[jackthecat]

so today i pulled the motor out and striped down the smallport gettin it ready to go in. found some really dodge shit here lol have a look at the photos.

motor about to come out.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505727.jpg

motor out
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505728.jpg

then takin the gearbox off found a big part of the block missing.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505729.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505730.jpg

then once the clutch was off it was all munched out. like this
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505731.jpg

so i looked into where the spigot bearing should be apparently they're optional and too top it off its a 6 bolt flywheel which means the block is 4ac, bill sherwood will tell u its a rare early modal 4age block but its not, its from bogan people using 4ac blocks to replace blowen 4ag blocks and some how i have managed to end up with 2 of these motors over my time i have been workin on e7's on the plus i now have 2 good flywheels for 7ages
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505732.jpg

and this is how the smallport is lookin just got to give it a clean and drop it in.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505733.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505734.jpg

[jackthecat]

so today i got the motor and box back in now just waiting on the t3 smallport itb manifold then will hook everything back up.
\http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505770.jpg
goin back in

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505771.jpg
back in with new extrators test fit. my 60mm rsr bolt on exhausts gets droped of this weekend, (i hope) so can get all that in before my surgery as i cant get under it for 6 to 8 weeks as i will be in a sling

[jackthecat]

so today i swapped my tacho dash for a clock one and 50 my way so i could fit in my autometer sport comp tacho.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505803.jpg

then i set out on geting it ready for the 2 seat mod plate.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505804.jpg

halfway through makin a plate for the gearstick just waitin on the 60mm holesaw for my gauges will use it to make the gearstick hole too.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505805.jpg

how the gauge plate looks havnt drilled it yet, so might change it up.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505806.jpg

then starting workin out how im goin to run the fuel lines a little bit, will be using all earls lines and fittings.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505807.jpg

[jackthecat]

so today i changed my rack bushes, put on my rear t18 bar and then next 60mm rsr exhaust

old rack bushes
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505867.jpg

have gained more lock from the 14x8-10 from the 14x7+7 as they dont hit on the rails anymore and have a much tighter steering feel (no play at all)
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505868.jpg
then changed the exhaust
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505869.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505870.jpg

then changed the bar
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/505871.jpg

[Sprinter Freak]

looking good dude, is the steering arm hitting the LCA in that lock photo?

[jackthecat]

looking good dude, is the steering arm hitting the LCA in that lock photo?

yer man its as much lock as i can get before notchin the lca.

bit of a thread update, have bought 1zz coil on plugs and a gze dizzy.
and looks like im goin to a silvertop quad with 130mm trumpets with a 10 degree bend on them to clear the clutch.
so my blacktop quads will be for sale on a stock blacktop manifold.

[jackthecat]

bit of an update.
won a 4agz dizzy one yahoo japan should have it next week, bought coil on plugs my new itbs rocked up.

the coil on plugs
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506089.jpg

and here are the new itb set up silvertop with custom 130mm trumpets with a 10 degree bend on T3 smallport manifold thats had it inside smoothed & polished
just need to swap my pajero master back to a stock one to clear the last trumpet.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506090.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506091.jpg

[Jacobxxx]

Fuck yes

So cool dude

[Jdm-Mcc]

Reminds me of pecks ke because red and star indicators

Reminds me of me of my bluebird because everything was fucking dodgey and had to be replaced haha

rad 70 dude, doing a sweet job!

[willa]

Reminds me of pecks ke because red and star indicators and because everything was fucking dodgey haha

rad 70 dude, doing a sweet job!

Fixed.


Lololol

[jackthecat]

thanks guys yer its were i got the idea for them star indicators.

couple more updates today. probably be the last update for a while as i go in for my shoulder reconstruction this friday.

gauges are in just need to be wired in,
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506130.jpg

booster in on and clears just....
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506131.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506132.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506133.jpg

[jackthecat]

http://www.youtube.com/watch?v=oQ1j-cZKr44its alive.

[Mika]

Looks killa dude, seriously thinking of running ITB's are seeing this.

[meadan]

Ahhh didnt realise you were on these forums.

But those stacks look better in your engine bay than they did in mine!

Looks awesome, come to raleigh in june!

[jackthecat]

Ahhh didnt realise you were on these forums.

But those stacks look better in your engine bay than they did in mine!

Looks awesome, come to raleigh in june!

yer man. im so happy with how they look. dont know if my car will be on the road then, goin in for my shoulder reconstruction tomorrow and am in a sling for 2 months, then rehab so dont know when i will be able to drive it, but once i can i will get it on the road.

[jackthecat]

little update got and polished my gz dizzy
my lsd landed but its kouki so im now tryin to sell it and have bought one with a 4.8 cw/p so sould get that soon

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506323.jpg

[jackthecat]

today i picked up some earls fitting to do my oil pressure and temp line to the tee piece.
1/8" BSPT to -3 for the oil feed on the block
1/8" NPT to -3 to go back into the tee piece
500mm of -3 braided earls line
1x an-3 by 45 degree bend
1x straight -3
1 x tee piece (still waiting on it)
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506520.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506521.jpg
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506522.jpg

then i test fitted my gz dizzy. goin to cut off the lug that the stock plug clips onto and polish it.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/506523.jpg

[Jman_KE70]

loving this build mate keep it up.

p.s
shoulder injuries suck good luck with the recovery

[jackthecat]

loving this build mate keep it up.

p.s
shoulder injuries suck good luck with the recovery

your not wrong, only been a bit over a week in a sling and im about ready to set fire too it., didnt realize how much rehab i have to do to be able to use it, only plus is im on Workcover. $707 a week after tax till im 100% fit to go back to work.

[willeE7]

Shoulders suck. Had a reconstruction each side. Here's hoping it never happens again.
Good on you for re-doing all of this properly. Keep at it.

[jackthecat]

to run my water gauge i had to drill my water neck out and re tap a new thread for the adapter
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/507100.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/945DD0C1-E685-4714-9287-BB6DF6F57357-4115-0000023D52C31281_zpsaa3d77e6.jpg.html)

bought wilwood pedal box has 3/4 clutch master and 3/4 and 7/8 brake master. dont know if i will use but would too to make room for 150mm trumpets

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/507101.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/5B4CF28B-949B-4035-8234-E60225625338-4115-0000023D43C6A925_zps94ba3c91.jpg.html)

finished off the oil temp and pressure tee piece

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/507102.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/52DE596C-E7AC-4F3C-B655-041D73970832-4115-0000023D5CBE586E_zps844a359a.jpg.html)

cant stop lookin at this motor since i cant really finish atm just lots of lookin

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/507103.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/7677CD11-6FAC-44FD-8AA9-C63A9A516393-4115-0000023D6AA41A06_zps2e198571.jpg.html)

[jackthecat]

couple updates

have bought a set of SSR MKIII 13x7.5-10 & 13x8.5-17 replace my 14" mesh which have now been sold, will also sellin the quads and flat front as im likely to bin the car out drifting so sell quads to hardparker and going to slant and painting the whole car white as i want to street this car, plus the glitter red would stand out to much.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/507247.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/D110935E-443D-4EA8-9123-151E2FC8FC28-2168-0000011189E4AB54_zpsacb364d7.jpg.html)

the end result just not as railed on 175/70r13

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/507248.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/12FA3F79-A0E0-447D-A331-C85A06062E7C-2168-000001118801375A_zps5e3ba410.jpg.html)

[willeE7]

Can anyone name those wheels on the car on the right??? ^^^^

[AJPS]

enkei apache?

[john84ie]

dont think so,i had a set of apache's in th past

[Seventy]

Enkei focus

[JDMWheels]

Correct ^ SSR have also made some as "Focus Racing"

[jackthecat]

so got out bid on the MKiii. had been watching them for 3 weeks and they just wernt selling so silly me only bid the min and lost them lol.

then today bought my MCNSPORT AVO 5kg rear coilovers they only came to $620 posted and got a w58 box cheap

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/507546.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/C0718DA2-997B-40B0-9676-C3D2E7EE3D92-124-0000000102F8285D_zps536dd784.jpg.html)

[jackthecat]

was at the wreckers today with slydar and found a silvertop 20v. so we started pullin the quads off it and just pulled the airbox off and found this. had quite the heart attack

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/507897.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/13050F60-9960-419E-A4D5-56F18B56757C-6063-000003E906863655_zps281b282b.jpg.html)

[LittleRedSpirit]

Scary. Python?

[jackthecat]

diamond python some one said on facebook all i need to know if snake fcuk that!!! lol. goin to go back tomorrow and poke it with stuff till it fcuks off so i can get the quads lol

[jackthecat]

bit of an update.
got my mcnsport avo coilovers.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/508439.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/527DE6FB-8D49-415E-A335-02033D404FA8-9411-000004935EB7DA56_zpsd018ef1c.jpg.html)
motor ready to go back in with the w58 on it.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/508440.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/5B0FA86A-EBA0-4006-A355-ECBA647DE3EB-9411-0000049372D1EF40_zps90e1edfe.jpg.html)
got my clutch built. NPC 3 puck with W box spline with my old exedy pressure plate.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/508441.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/433DB97E-41B8-4C9C-B7D0-C25A167CDFAB-9411-00000493589180A3_zps1d9b63a6.jpg.html)
how the shifter fits with the AZ custom adaptor was able to use a ra60 front tailshaft with it too. just had to make the tabs to bolt it on 10mm wide for the bolts to fit.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/508442.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/ACF2AC49-D8BC-4E25-A35C-793AD385E73D-9411-00000493517F3CDE_zpscff1ddf6.jpg.html)
had to build up a gearbox crossmember. this is the template never got a photo of the finished crossmember looks the same as this
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/508443.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/7027444F-FB49-48B6-AC35-F6CA8B8A5671-9411-000004934C296569_zps5df92833.jpg.html)

[jackthecat]

so motor is back in loom all tidied up with all the gauge sensors wired into the loom. and have started welding on my front on rear guards.
top photo. about one month of owning it and had already started the tiding of it, bottom one was today
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509242.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/DC3E8B21-CB92-49C5-8114-DA5C9D7659DA-6975-0000036D1CF2DBE4_zps93159853.jpg.html)

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509243.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/77EF6CEB-E896-4867-832C-7DF77C72AC9A-6975-0000036D30370F31_zps90011f46.jpg.html)

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509244.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/6970437B-B524-433D-A5B9-AAFAC24BBFDB-6975-0000036D40A6F03F_zps6e1449e1.jpg.html)

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509245.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/F39B7D81-66B9-4BF7-AD62-D48DD26D8261-6975-0000036D4AC41723_zpsd7a37b79.jpg.html)

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509246.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/DBF51309-9C41-4BBA-AAE9-7666582D7013-6975-0000036D58045D77_zps776b88d7.jpg.html)

about to start on this side then get it painted all white my hoshino 14x8-7 wheels should be here on Tuesday too so very excited

[jackthecat]

so this week has been amazing. my hoshinos landed, i found a pair of miss mactched velo seat one gpt-1 and one gp90 on gumtree at the right price and i swapped my pair of hayashi streets with a mate with cash 450 cash his way for a set of 14x7.5+3 ssr formula mesh. just got to pick up the last wheel from his.

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509420.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/23068623-5755-43F0-BD64-605A07D87259-12750-00000658A7B8282A_zps0b711322.jpg.html)
started my sticker collection
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509421.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/000EBA5E-62FA-4BD6-98F1-204DD5474D03-12750-00000658B3C5283C_zps39f5b358.jpg.html)
starting my wheel collection
14x8-7 hoshinos and 14x7.5+3 ssr formula mesh
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509422.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/E627B311-30DD-4336-8740-0BFA6ECC4C72-12750-00000658AD99DB62_zpsd300b68a.jpg.html)

[AJPS]

you seem to be missing some stickers jack

[jackthecat]

i know dave only ajps sticker is on my window of my car. will have to get more off u man. put the tires on the hoshinos yesterday will post up some photos off it soon.

[jackthecat]

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509448.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/099723A9-810B-4F63-9326-806FA5BEEB90-13774-000006E975AF12DF_zps9fc4964e.jpg.html)

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509449.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/32BE4113-F46D-4679-BD49-E2A48FB1C7EA-13774-000006E97FACB286_zpse1401643.jpg.html)

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509450.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/FFA16081-861A-4F72-B481-EAD9F526274F-13774-000006E987E2890A_zps569430f2.jpg.html)

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509451.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/58F81C75-4F75-4417-8D39-BF9B848208FB-13774-000006E990FF79F4_zpsebe03f35.jpg.html)

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509452.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/A14D4D68-0453-497A-AB0F-F995E02D8B78-13774-000006E99CDF0F79_zpsb0443ae7.jpg.html)

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509453.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/53B64E25-1AC5-486C-AB95-F3C5D65679BA-13774-000006E9A3FE1BFF_zpsfd373c4a.jpg.html)

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/509454.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/D6B45B9F-63B9-4278-A399-C55B72E9FAF7-13774-000006E9AEBB8262_zpsd90a0b6a.jpg.html)

[jackthecat]

got some traction brackets off gumtree the other day 120 bucks for ajps ones not bad. hopefully will stop being lazy and do my other rear guard this week and post photos.

[jackthecat]

so it only took 3 weeks but finished the other rear guard in about 1 hour just have to sand them both now
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/510162.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/DA12A044-9900-405B-AC30-5E47C8C12AD6-33745-000010D94E087E5C_zpsef51e11d.jpg.html)
also got a walbro gss342 intank pump for free off a mate (goin to us as a lift pump) and get a ajps under car surge tank also got a sard fuel pressure reg off him for free too. :P
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/510163.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/9622A2ED-97C1-4C06-BE1D-F536BC940AB8-33745-000010D9541A002C_zpsd03f0c9d.jpg.html)

[jackthecat]

so i got very bored today so i railed my car, rears can go 30mm lower but tires are hitting on the top of the inner guard. didnt cut/ hammer enough when i did fronts on rears.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/510207.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/8CF2300A-4162-41BF-B5BD-4B21CBC7A676-34586-000011334E8ABB01_zps8de94a0d.jpg.html)
wouldnt roll with out scrubbing bad had to wind it up 10mm to make its roll with out scrubbing the top of the inner gaurd.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/510208.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/C8AE8209-CD83-485F-9140-D068E55D0400-34586-000011335510CF6A_zpsc7c14865.jpg.html)
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/510209.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/86E1AA21-149A-488E-9C9C-22BA207E9A58-34586-00001133634D7C39_zps0310ab58.jpg.html)
and this is how it was before i railed it.
http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/510210.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/528658B5-6DA3-4F7C-8BC5-197C56E15B3B-34586-000011337A02D970_zpsc3de1713.jpg.html)

[NIZLAH]

Rad build mate, loving the progress... all the best with your should recovery

[jackthecat]

so project $200 respray with 4L of primer 4L of acrylic white 8L of premium thinners and 4L of wax and grease remover was at super cheap and all the paint was on sale. got my ghetto on used a belt sander to sand the bog on the front on rear guards. used the same trick on my t18 when i did front on rears with slydar he did the welding and showed my the tricks of the trade. this was my 1st time doin fronts on rear myself think i went ok. will post photos of other side once in primer. was only goin to prime the guard but had left over paint so did the whole panel did the doggy and only wax and grease removed the rest of the 1/4 panel. once the other guard is in primer goin to wash the car with a scourer to rough it up.

http://www.ae86drivingclub.com.au/dcimages/5/5/3/5/510227.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/C8A1220B-49D3-483C-B066-207BD5B77640-35315-0000118ACC6B2875_zpsf35774f9.jpg.html)

[jay70]

Wish it wasn't a slanty. Haha nah cool build man. Should be pretty sweet

[Vaughn]

slantfrontlyf is there a problem?

How do you like your rear coilovers? 6kg?

[jackthecat]

there 5kg i havnt driven on them, but lots of good things have been said about mcnsports

[jackthecat]

only took 4 months for me to start painting it far from good, good from far hahaha heres some photos from today painting the doors and hood and boot today
http://www.ae86drivingclub.com.au/dcimages/515504.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/FF4E9701-460F-4AD5-92D5-E5F0BF0C5F24-2143-00000240D3F0C8E9_zps5ab411a6.jpg.html)
got my self a CDT Gemini S3 turbo vent off a mate. i think it looks cool over the trumpets. going to paint it black today
http://www.ae86drivingclub.com.au/dcimages/515505.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/4D9799DC-84DA-4BB2-BFA0-DDD1B4045AA4-2143-00000240DB625221_zps7000367f.jpg.html)
http://www.ae86drivingclub.com.au/dcimages/515506.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/5DF95112-86FD-44E1-8C78-5809AEA2B1BA-2143-00000240E1F2E40E_zpsf0802879.jpg.html)

[jackthecat]

so i finally did it. goin to start putting it back together and get a quick tune for the motor and get it mod plated and regod in the next 6 weeks i hope. then i plan on building up my 7a bottom end and get a good tune to use once im bored of the 4a or its blows as the rings are on the way out.
http://www.ae86drivingclub.com.au/dcimages/515511.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/83DFEB12-0196-4AA9-825D-B5C50ED97CCC-2509-000002B5B46EE854_zps56b98cbd.jpg.html)
http://www.ae86drivingclub.com.au/dcimages/515512.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/26E99FA5-7F3B-438C-9345-DF3B97ED5AD1-2509-000002B5C6CFA3D8_zps99bb4a40.jpg.html)
http://www.ae86drivingclub.com.au/dcimages/515513.jpg (http://s1340.photobucket.com/user/Jack_Esders_Lovell/media/4257E03A-60FD-4993-91D2-AE4F1A585AC0-2509-000002B5EE84ECA3_zpsc2b51ff7.jpg.html)

[Zane k]

How is this thing coming along?!?