51EEPA The ST141 Corona

[51EEPA]

Time to EDIT this! LOL

Hi All,

This is my ST141 Corona i bought off a family friend about 8 month ago, track/weekend car.

31517
339133391433915

Motor
450rwkw 3sge beams (gen 5)
Carrillo H-Beam rods
Toda 285/280 cams
Toda 8.5:1 forged pistons
Toda metal headgasket
Toda valve springs
Custom sheetmetal intake manifold
70mm billet throttle body
Custom exhaust manifold
Borg Warner EFR 8374
MRP oil sandwich plate with thermostat
Custom twin entry fuel rail
1800cc injectors

ECU
Emtron KV8

Gearbox
6 Speed sequential
Direct Clutch Services custom clutch

Diff
Unknown, maybe hilux or an irs conversion

Brakes & Suspension
Wilwood 4 pistons calipers (front)
Winmax race pads
Brembo 280mm discs
BC gold coilovers front
BC gold adjustable springs & shocks rear
AJPS rosejointed lower control arms
AJPS extended tie rods
AJPS 50mm RCA's
AJPS lock spacer

Interior
Bride Lowmax bucket seats
Custom seat rails & mounting positions
Takada harness'
Nardi steering wheel
Digital dash
ASD hydraulic handbrake
Fuel
E85
Walbro intank 460lph feed pump
Aftermarket Industries surge tank with 2 x Walbro 460lph pumps

Wheels
Riverside R101
Front 14x7-3
Rear 14x7-3 but will be cut up and widened once diff is decided!
Possibly 14x8 or 14x8.5-20 something!

[djconfig]

looks like its going to be a grate build! very much the same thing i want to do to my celica.

keen for updates keep up the good work. ^_^

[sundee]

goodluck! looks like a sweet base

[51EEPA]

SSR MKII's are on the way, not sure whether i will drive with these daily or not :/
14x7.5-6
14x8-0

31560

[51EEPA]

New Clutch & Flywheel on the way!
Toda Chromoly 5.8Kg single mass flywheel over the standard 13.9kg dual mass flywheel.
Toda metallic clutch disk and new clutch cover :)
31598

[troublesome_7]

Nice car mate.

What you doing with the standard borgy diff?

Michael

[51EEPA]

Im just going to weld it up for now.
Later on will probably put a f series in with a 4.7 ratio.

[drift kid]

Looks like it's going to be a weapon of a car, some decent coin going it's way, keep it up

[troublesome_7]

Should be good son!

Those Borgy's are shithouse, will be good for the wet though. You should destroy it in no time with that beams, or an axle at least lol!

[macca1590]

loving the sun shade!!

[jay70]

good work man. some nice parts going in to this

[51EEPA]

Only keeping thw borg warner in there for the 4.11s.
Can't wait for 4.7s though!

[troublesome_7]

Dats it, the boy knows his shit :thumbup:

Good tuned exhaust, modified cold air intake/TB, minor fuel setup and Ecu + 4.77's will be the shit!

Should be sweet as.

[mexr69]

Heyyy bro its nissan silvia spears
Awesome its coming alone well can't wait till mines built! !!!!

[INVSBL]

whats you plan for engine mounts?

gonna just piece bits together or custom fab stuff up?

[51EEPA]

Standard 2sc engine mounts bolt up to the 3sge block! so its just a matter of bolting them on and throwing it in!
Also on the way are the following:

Rosejointed lower control arms
Longer tie rods
Lock spacer with slip on :)

Also got stuffed around with the Toda clutch from japan.
So i ended up going with the ORC clutch instead, similar clutch although the flywheel is 4.8kg instead of 5.8kg.

At this stage i will 100% not be making my deadline of 21st of may.... lol
Hopefully should be finished by the end of june for its daily duties!

[51EEPA]

Well, seeing as im not going to meet my deadline i have changed up a few things :)
I was recently talking to Scott Kuhner from Insight Motorsports, he has given me a ripper deal on his new EmTron ECU which will now be wired into the car!
31859
Along with the ecu there is also a ITB adapter and BlackTop ITB's on the way, set up was for a friend but he offered to sell it to me so my car is on the road sooner :)
31860

[drift kid]

Haha yeah my "daily" hilux was meant to be a 1 month Xmas holidays build, almost five months later... lol

[51EEPA]

ORC clutch, 4.8kg flywheel and both bearings arrived today!
32033

[51EEPA]

Wilwood 276mm discs with 4pot calipers and race pads installed, was going to run some SSR MKII's but the caliper hits the tapered lip they have unless i run a 8mm spacer(not running 8mm spacer)
So next choice of wheels will be Riverside R101's, probably 14x7.5-6 front and 14x8-8 rear.
321653216632167

[51EEPA]

well, whilst waiting for parts...
as we all do i have changed it up again!

i've had a turbonetics gtk-450 and an intercooler sitting on my bench for about 6 months, so i've decided to run both quad throttle bodies and the turbo :/
interested to see how it works! 11:1 motor and probably 7psi, obviously will be running a flex sensor for e85 later on when it's not well a daily haha!

Also found myself a set of riverside R101's 14x7.5-3 and hopefully have my hands on some R101's 14x8-6!

[51EEPA]

aaaaannnnnndddddd here we go.

Turbo blasted so it can have a elbow welded off it
32821

Riverside R101's
32822

Quad throttlebody idea is scrapped, doing a custom sheet metal intake manifold with a billet 80mm throttle body.
Steampipe exhaust manifold.
Screamer pipe as loud as your mum was last night.

[51EEPA]

Front suspension and brakes are sorted now!
Next on the list is to sort out diff and rear brake setup.
33273
33274
33275
33276
33277

[51EEPA]

ok list keeps going...
Aftermarket Industries 2.6L surge tank with Holley Dominater 1800 fuel pump with 2 earls fuel filters inside the surge tank.
33283

Racepak digital dash!
33284

[51EEPA]

Smallish update on the original post... LOL