Page 4 of 4 FirstFirst 1 2 3 4
Results 31 to 38 of 38

Thread: How To: Flare Guards

  1. #31
    Site Supporter Low Style's Avatar
    Join Date
    Nov 2008
    Name
    Jon
    State
    QLD
    Location
    Durack
    Country
    Australia
    Posts
    1,277

    Default

    where can i get a dolly from?

  2. #32
    Ok
    Join Date
    Nov 2008
    Name
    Seamus
    State
    QLD
    Location
    Milton
    Country
    Australia
    Posts
    1,860

    Default

    supercheap/repco

  3. #33
    Gone
    Join Date
    Dec 2008
    Name
    Joel
    State
    NSW
    Location
    Picton
    Country
    Australia
    Posts
    4,042

    Default

    supercheap, brought a whole kit w/ 4 dollies and 3 hammers for 20 - 25 bux

  4. #34
    Senior Member Mr Awsome's Avatar
    Join Date
    Mar 2009
    Name
    Dave
    State
    SA
    Location
    Plympton
    Country
    Australia
    Posts
    610

    Default

    there ok for this but the cars sheet metal its to hard for the supercheap kit and will dent the crap out of the dollys and hammers. get a decent GPI set (last ya good 10yrs if ya look after them) for ya back yard work, you and your car will love you for them. (there cheap $150-$250) but there more then decent enough for all pannel work on your car. get a metal file $50-$100 for an awsome finnish.

  5. #35
    Gone
    Join Date
    Dec 2008
    Name
    Joel
    State
    NSW
    Location
    Picton
    Country
    Australia
    Posts
    4,042

    Default

    im pretty sure 99% of guys on here would take the super cheap option for hammer and dolly set, for a job that is only done a few times i couldnt warrent sepending even near $100 for a dolly kit etc.

    best file ive found is the good ol flapper disc on a grinder, 120 grit and smoother finish than a babys bum

  6. #36
    Senior Member
    Join Date
    Feb 2010
    Name
    Andy
    State
    NSW
    Location
    Penrith
    Country
    Australia
    Posts
    113

    Default

    Hey everyone, sorry for digging up an old thread but i was told a ke70 front guard arch will fit on the back arch of an ae86 and am considering this to remove my flares as they are quite messy and hacked underneath and also can help me get lower due to arch being welded on abit higher. Would just like to know if anyone on here has done this? some tips would be great and sorry if this is in the wrong thread i did abit of searching and had no luck.

    Thanks

  7. #37
    Junior Member
    Join Date
    Jul 2010
    Posts
    6

    Default

    Great write up mate!

  8. #38
    Gone
    Join Date
    Dec 2008
    Name
    Joel
    State
    NSW
    Location
    Picton
    Country
    Australia
    Posts
    4,042

    Default

    Ke70 arch's wont fit on an 86.
    you will notice ke70 front are a "full" flare - but the ae86 is only 3/4 because it stops at the rear bar.
    You can put fronts on rears but you need to keep it either ae86 or ke70, their not interchangable, + when you do do it you also need to "cross" the flairs over
    SO - FRont Right goes on back left & Front left goes on back right.

    And Whoever owns that yellow 70 up top needs to loose the Sigma LCA's or S13 LCA's - way to much track
    even if you folded out both lips you wouldnt even go near getting close to the outside of that wheel.
    also - if thats a 195/50 that rim must only be 6 - 6.5" wide

Page 4 of 4 FirstFirst 1 2 3 4

Similar Threads

  1. Best way to flare guards
    By Gabe in forum Technical - Questions
    Replies: 24
    Last Post: 22nd December 2011, 10:25 AM
  2. Need someone to come out and flare my guards.
    By troy in forum Melbourne & Vic Events and Discussion
    Replies: 11
    Last Post: 28th May 2010, 11:47 AM
  3. Anyone know of someone who can flare guards?
    By Big T in forum General Topics (No Technical Questions)
    Replies: 0
    Last Post: 2nd February 2007, 11:03 PM
  4. Those Flare guards
    By Golberg in forum General Topics (No Technical Questions)
    Replies: 9
    Last Post: 26th July 2006, 10:01 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •