Page 14 of 40 FirstFirst ... 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 ... LastLast
Results 131 to 140 of 400

Thread: Universal 3sge (inc Beams) into AE/KE thread

  1. #131
    Moderator Sam-Q's Avatar
    Join Date
    Dec 2008
    Name
    Sam
    State
    VIC
    Location
    Endeavour Hills
    Country
    Australia
    Posts
    4,242

    Default

    so I can use bits from the FWD corollas? neat because they are a whole lot easier to come by than supra boxes.

    Now I have a pic:



    Here is my guesses:

    1- off the bottom outlet pipe to the heater core and one side of the throttle link? dunno about the other connection on the top

    2- Oil return

    3 and 4 the same? going to the throttle and the heater flow control tap and then the heater core?


    Not that I want to do this conversion for a very long time but I am curious. It doesn't look all that hard to do.

    So anyone have an opinions on shortening the bottom of the sump a little?
    My website: SQ Engineering - 4AGE and 3SGE upgrade/replacement parts

    - SQ Engineering on facebook -

    Please e-mail to contact me instead of sending a private message on here.

  2. #132
    Glenn ke_70's Avatar
    Join Date
    Dec 2008
    Name
    Clay
    State
    SA
    Location
    Barossa!
    Country
    Australia
    Posts
    5,311

    Default

    what part of the sump sam?

    you can cut a hole lot of the alloy bit and drop the motor atleast 20mm more. drops the sump pan extremly low though.
    theres now alot of room to widen the pan alot either.

    id love to here what other have to say about it as i want to drop my motor alittle more because it will foul on the tunnel when i move the shifter forward.
    Last edited by ke_70; 20th January 2011 at 10:19 AM.

  3. #133
    Glenn ke_70's Avatar
    Join Date
    Dec 2008
    Name
    Clay
    State
    SA
    Location
    Barossa!
    Country
    Australia
    Posts
    5,311

    Default

    whats that plug to the left of no.2?

  4. #134
    Senior Member Anthony's Avatar
    Join Date
    Nov 2008
    Name
    Anthony
    State
    QLD
    Location
    Brisbane
    Country
    Australia
    Posts
    831

    Default

    I see a battery terminal to the left of 2???

    Thats pretty much right Sam. 3 and 4 are the coolant supplies to throttle (anti icing) and heater. 1 is the common coolant return rail from those two. 2 is an oil drain. I am currently working on a new rear housing that is much lower in profiles as I find this to be a big part of the puzzle in fitment.

    Is that your engine??

  5. #135
    Glenn ke_70's Avatar
    Join Date
    Dec 2008
    Name
    Clay
    State
    SA
    Location
    Barossa!
    Country
    Australia
    Posts
    5,311

    Default

    woops i ment 4
    Last edited by ke_70; 20th January 2011 at 05:44 PM.

  6. #136
    Senior Member
    Join Date
    Dec 2009
    Name
    Andrew
    State
    California
    Location
    Nothern
    Country
    USA
    Posts
    305

    Default

    You meant 2? Or meant 4?

    To the 'left' of 4 is the RF frequency suppressor, it's connected to the ign coils negative wire.

    Andrew

  7. #137
    Veteran Andy San's Avatar
    Join Date
    Jan 2009
    Name
    Andy
    State
    SA
    Location
    Adelaide Hills
    Country
    Australia
    Posts
    1,111

    Default

    Another quick question,

    If I block off 4 and 3

    can I remove 1 from the back of the water pump and not cause any problems?
    Andy

    Quote Originally Posted by slide86 View Post
    I will however take take the water from the washer bottle posted to a boat in the southern pacific....express please

  8. #138
    Senior Member
    Join Date
    Dec 2009
    Name
    Andrew
    State
    California
    Location
    Nothern
    Country
    USA
    Posts
    305

    Default

    You could. I'm not too sure how that will affect the cooling system/cylinder head flow though.

    Andrew

  9. #139
    Senior Member 4.5AG's Avatar
    Join Date
    Dec 2008
    Name
    Vener
    State
    NT
    Location
    Lyons
    Country
    Australia
    Posts
    267

    Default

    Ant, how are you going with the new housing?
    Is it available for sale yet?
    Also if I'm using quads and no heater core, can I join 4 and 1 together using a u shape hose and also can I divert # 3 hose to pipe no 1

  10. #140
    User fantapants's Avatar
    Join Date
    Dec 2008
    Name
    Pat
    State
    TAS
    Location
    Other
    Country
    Australia
    Posts
    1,635

    Default

    thats how i did mine 4.5
    RIP Carly - a smile to light the world.
    06/07/2011

Page 14 of 40 FirstFirst ... 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 ... LastLast

Similar Threads

  1. What did you do on your ae/ke today thread
    By dove grey 64 in forum Melbourne & Vic Events and Discussion
    Replies: 329
    Last Post: 19th December 2013, 01:49 PM
  2. 3SGE Beams
    By Jacobxxx in forum Ebay Items - My Stuff
    Replies: 1
    Last Post: 29th October 2012, 12:03 PM
  3. 3sge Beams Coilpack
    By HiroshiFumi in forum Cars or Parts Wanted
    Replies: 2
    Last Post: 14th January 2012, 06:33 PM
  4. Replies: 12
    Last Post: 29th November 2010, 09:00 AM
  5. beams 3SGE questions
    By ke_70 in forum Technical - Questions
    Replies: 6
    Last Post: 22nd May 2009, 07:50 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •