Results 1 to 4 of 4

Thread: Toyota TWINCAM history

  1. #1
    Senior Member 4.5AG's Avatar
    Join Date
    Dec 2008
    Name
    Vener
    State
    NT
    Location
    Lyons
    Country
    Australia
    Posts
    267

    Default Toyota TWINCAM history

    από KP61 » 05/12/07 19:10


    2tg
    3tg
    18rg

    Toyota Twin-Cam History


    Toyota is the largest producer of TwinCam engines. Toyota offers more TwinCam models than any manufacturer. Here is a brief historical outline to the milestone Toyota engines of the TwinCam variety and the race engines they are based on.

    The earliest and rarest production Toyota TwinCam engines were the 3M and 9R. Both engines were produced during 1966 to 1968, and ironically did not carry a G engine designation. The 3M was a 2 valve twincam 6 cylinder engine with triple Mikunis used in the 2000 GT. The same block, modified through the years became the 5MG/6MG/7MG engines- with a totally different head. The 9R was a 2 valve twincam 4 cylinder with twin Mikunis used in the Corona 1600GT.

    The 2TG was introduced in Japan 1970 for the Corolla, Sprinter series in Japan. It was available in various forms (through the years) until 1984. The 1600cc 2TG came with twin-side Mikunis in 2TG, 2TGR, and 2TGU models. Eventually it came with fuel injection as a 2TGEU. The last model in this series engine was the 3TGTE (although it was never available in the Corollas). In the US, these engines were popular in Corollas, Carinas, Dune buggies, and Lotus 7 replicas. The 1750cc and the 2000 cc conversion were extremely popular and more reliable than the later 2140 versions.

    The 18RG was first introduced as an 8RG and as an interim 10RG (both 1900cc) in 1971 for the Celica GT models and the Mark II, respectively. The 2000cc 18RG came out in 1974 with twin-side Mikunis in 18RG, 18RGR, and 18RGU models. Eventually it came with fuel injection as an 18RGEU. In the US, these were popular in Celicas, Pick-ups, and Dune buggies. The 2200cc conversion was very popular and some were even setup as 2400cc.

    In Toyota-speak, the G designation means TwinCam Sport type. For both 2TG and 18RG engines: the extra R designation denoted regular gas (lower compression); the U denoted emmission controlled. For all other TwinCam engines: The additional letter designations after the basic engine model mean: E for fuel injection, T for turbo, Z for Supercharger.

    The 2TG and 18RG were the original production Toyota TwinCam engines. These were the most widely available and produced TwinCam engines for production cars in the whole world (in that era). Even Lotus (with their own Ford-based engines) tried to buy and use these engines. The use of these engines in competition saw many major victories for Toyota world-wide. The 2TG was more developed in terms of parts from TRD since it was widely used for both racing and rallying. The 18RG was used mainly for rallying, most notably by Toyota Team Europe, but similar race specification parts that the 2TG had were also available from other sources. Toyota also produced a limited number of twin-plug 18RG that never reached production.

    The 3TGTE, a twin-plug version of the classic 2TG and 18RG cylinder head design- with a turbo was the last model utilizing the bullet-proof and trouble-free 8-valve heads. This model replaced the 18RGEU in the Celicas in 1983. In fact the latest models 2TGEU and 18RGEU shared the same valves and valve train components. The 3TGTE was the base for the 4TGTE homologation engine for Toyota's Group B Rally Car. This engine, in the highly competitive and eventually cancelled Group B SuperCar class in the FIA World Rally Cup series, took Championship honors. Group B was cancelled This was a fitting tribute to the outstanding technical design of the 2TG and 18RG heads and blocks, before the whole world used 4 valves for everything.

    The ultimate versions of both the 2TG and 18RG were made by TRD- they were known as the 151E and 152E respectively and came with 16 valve heads, both were available in carburetor (50mm Mikunis) and fuel injection (mechanical Denso) models. There was also a 150E 16-valve version of the 3K / 4K engines. These 16 valve heads were the forerunners of today's 4AG, 3SG, 7MG, and 2JZG engines. These were race only non-production heads, with heavily modified blocks. The 152E race engine was used for US Toyota's early back-to-back victories in desert/stadium racing and IMSA GTU events. The 152E was used in Europe for the FIA World Rally Cup series.

    The most famous and successful Toyota Race engine- the 503E was used in Toyota's Triumphant Championship seasons in IMSA GTO / GTP, Pikes Peak, Le Mans, and in the mid-90s Japan Touring Cup Championship. It is important to note that the 16 valve cylinder head layout from the 152E engine and the T block crankshaft saddle design were used as design base for this ultimate Toyota 4 cylinder Turbocharged race engine. The 503E represented the most powerful 4 cylinders in competition history developing over 1000HP in qualifying tune, 800HP for sprint races, and 600 for endurance events. IMPRESSIVE.

    The 5MG and 6MG were both 6-cylinders introduced for the MA60 series Supra and high performance sedans in Japan. These TwinCams ushered in a new generation of TwinCam design and application. The innovation of self-adjusting hydraulic lifters, required no extra maintenance for the valve adjustment. This promised service simplicity to the average Toyota mechanic. The towering cam position was impressive and heralded the arrival of the 6 cylinder TwinCams.

    The 4AG and 1GG engines introduced the new generation 4 valve TwinCams of the "G" engines. This represented the 4th production generation TwinCam heads. The 1600 4AG was the 4-cylinder version and the 2000 1GG was the 6-cylinder model, both were available with or without superchargers. The 3SG and 7MG soon followed with or without a turbocharger. All true high performance Toyota engines carry the G designation, including the new 1800 2ZZGE. The newest G series engines use up-graded features- variable timing, variable lift, 5-valves, independent throttle bodies, supercharger, turbo, and even twin-turbo!

    Most current Toyota in-line 4 or 6 production engines have a G model version, except the Tercel, which makes do with a 4EFTE engine, a turbo variation. The "G" engine guaranteed the Toyota driver- performance above par. The "F" designated engines are also TwinCams but are not the performance models. The F engines are designed for normal low rpm, high torque, and quick response. Most of the current Toyota engines use an F type cylinder head, including all the V6 and V8 engines, enabling Toyota to continue claiming to be the world's leading supplier of the TwinCam engine design.

    The Yamaha connection needs to be mentioned: Yamaha developed the Toyota 2000GT and was a partner of Toyota in the design of most successive G model heads. Most G engines/heads, including the 3SGE/3SGTE (now in it's 3rd generation), the Previa specific 2TZFE/Z (no relation to the old T engines), and the newest 2ZZGE engines were and are still designed and cast by Yamaha. The 4AGE and 2JZGE heads are proprietary Toyota designs and manufacture, although many components are still made and supplied by Yamaha.

    Toyota's "G" production engines in Motorsport trim and competition tune is unmatched by any engine manufactuer. The 4AGE is the successor to the 2TG, as the 3SGE is to the 18RG, in the important 1600 and 2000 class of racing engines. Both engines in their respective classifications are used widely in Formula type competition. The TRD Formula Atlantic 1600ccc and TOM's Formula 3 2000cc engines showcase the design integrity and tuning capability of both production engines. They are all proven winners, they are all production based.

    The Toyota TwinCam engine is Toyota's only claim to a technical heritage or legacy in the automotive industry. The classic TwinCam design has worked very well for Toyota and has powered all milestone Toyota models. The new 3rd generation 2JZGTE, 3SGTE, 2ZZGE engines, updated with Dual Variable cam timing and lift- showcase the ultimate Toyota performance engines. No other manufacturer can claim over-all superiority on production based TwinCam engines, although other manufacturers are currently able to exploit the benefits of TwinCam technology further. Toyota will have to reclaim this historic edge and actually raise their design parameters to match the other trend-setting TwinCam introduced by other manufacturers.

    Toyota's high profile entry in Le Mans, WRC, CART, and soon Formula 1- is highly anticipated by Toyota enthusiasts and competitors. More important to diehard and prospective Toyota enthusiasts is to have the most sophisticated and advanced TwinCam engines under their hoods, and in their cars. The historic role of the Toyota TwinCam engines in Toyota's place in the automotive industry was very crucial and important. In focusing sharper into Motorsports, Toyota must protect and not forget the important formula- TwinCams in Toyotas.




    Toyota built their formidable Twin Cam reputation on these engines. Based on the popular T block and R block of the early 70's, these engines were the envy of all car manufacturers. These engines evolved- from the early stock ohv and sohc variety to the pure high performance G models, then the smog controlled models, and finally the fuel injected and turbo models. Originally the 2TG (1588cc) started at 115 HP, and the 18RG (1968cc) at 145 HP. Both engines had a twin- the 2TGR and 18RGR which had low compression pistons, but identical cylinder heads. In the mid 70's both the 2TGU and 18RGU saw a further drop in compression, emission controlled carburetors, and shorter duration camshafts. However, the heads were upgraded with bigger valves and hardened valve seats (for unleaded fuel). Horsepower figures typically dropped about 10/15 HP. By the late 70's, the fuel injected models arrived as the 2TGEU and 18RGEU, to regain all the lost horsepower. These models, despite still shorter duration cams and lower compression, had the best cylinder heads with still bigger valves.

    The 3TGTE (1770cc) replaced both engines by 1983. The well-proven head design- now had 2 spark plugs per cylinder and a turbocharger to develop 160 HP. Despite claims of Toyota that the 503 race engine was based on the 3SG design- the bottom end was patterned after the 3T block (which had become wider in the lower block skirt to accommodate the longer stroke crankshaft. The crankshaft saddles are identical!

    The competition models of the 2TG and 18RG, developed with parts from TRD saw many worldwide wins for Toyota- Corolla Levins, Sprinter Truenos, and Celica 1600 GTs with the 2TGs. In Asian and European Formula racing, the 2TG in the 1600cc category regularly beat all the other engine manufacturers. The Celica 2000 GTs saw many race and rally victories worldwide, including the European based WRC (World Rally Cup).

    In the ultimate WRC Group B series, "the super class" in the World Rally Cup- the 4TGTE (homologation model of the 3TGTE) powered the Celicas of Toyota Team Europe to the Championship. The Group B class was soon cancelled after the general public and some rally entrants protested that the cars were unsafe because of the powerful engines.

    The ultimate versions of the 2TG and 18RG were the 151E and 152E. These were not production engines. The heads and blocks were not interchangeable to the production units. (These heads were the design forerunners of the 503E heads.) Both engines had 4-valves per cylinder with either carburetors or mechanical fuel injection. These racing heads were fitted on heavily modified T and R blocks- basically to accommodate the new heads’ chain set-up (for the fuel injection and the dry sump oiling system). Originally they came in the same 1588cc and 1968cc configuration that were targeted to the specific 1600 and 2000 classifications for FIA (Federacion Internationale Automobile) regulations. For the U.S. IMSA (International Motorsport Association) the 152E was bored to 2200 to qualify in the "under 2.5 class"- normally aspirated at 330 HP.

    The first race engine based on the 2TG was made by TMC (Toyota Motor Corporation) in 1970 and was known as the 100E. Toyota built about 25 engines with full racing specifications- specially casted head (11111-______) yes, blank numbers!, special intake manifolds, dry-sump oil system, 50mm Mikunis, ND igniter and instrumentation, ND fuel pump and some other trick stuff. Of the 25 engines- 8 went into Corollas (Levin and Trueno), 10 went into Celicas, and the rest were spares. Eventually TOSCO (Toyota Sports Corner) was organized and some parts from this project became available individually. TOSCO later became TRD.

    The success of these engines has been greatest in the streets. The Celicas with built 18RG could outrun the 240Zs and Skylines, of that generation. The Levins and Truenos with prepared 2TGs outran all Japanese models and all European Twin Cam models- the Alfa-Romeos, Lancias, including the Lotus Cortinas and Escort Cosworths (of the 16-valve BDA variety. The Toyota Twin Cams was regarded highly by all competitors. It was the envy of the other manufacturer tuners. Some tuners in European formula racing made valve covers with their corporate names, to hide the Toyota origin.





    MODIFIYING THE 2TG AND 18RG

    The 2TG and 18RG, in all the different varieties- offer immense tuning combinations.

    Block: The 2TG blocks were similar to the 2T and 3T blocks of the same year generation. For modification purposes the 3T block is preferred because it has the longer stroke crank, and with a bore-up to 89mm becomes a 2000cc. The later model 2TGEU block is the same as the 3T, and will take the 3T crank with no modifications. The 2TG stock block can be bored to 1750cc, with a similar bore-up to 89mm. To fit the 3T crank in an original 2TG block can be done with a lot of work- grinding the inside of the block skirts to clear the rods. The 2T and 3T cranks are forged. There is also available a 2150cc. using a modified Toyota 4Y crankshaft. The 4Y crank is not forged, but there is an aftermarket steel billet unit. In converting a single cam block to a twin cam, aside from switching over all the front valve train components, the original cam bearings have to be turned and repositioned. You must have a complete donor Twin Cam to do the conversion. Installing the 2TG into any T engined Corolla is a bolt-in deal with no modifications to the crossmember or brackets.

    The 18RG block can be bored to 2200cc (92mm) or stroked to 2400cc (using a modified 20/22R crank). No the 18RG head will not bolt on a 20R/22R block! The stroker crank is not recommended. Aside from the very expensive to modify to fit the 18RG block, it seriously cuts into the revving characteristic of the Twin Cam. The 18R blocks did not change that much, but installing into the later model pick-up and Celica will need the newer block that have the extra engine support holes embossed on the sides of the block. Because of the wider variety of models the engines originally came in, there are 4 different oil pans, six different engine brackets. Fitting into specific applications will be a matter of matching the oil pan configuration to the original engine; and the engine brackets to the width of the crossmember. On the older Celicas with the 18R engine- it is a bolt on by using the pan and brackets off the original engine.

    Cylinder Head: The early generation 2TG and 18RG heads had the best camshaft profiles and carburetors. They will respond extremely well to porting and big valves. If the block is bored out or the compression raised, longer duration cams will be needed. The mid-generation 2TGU and 18RGU heads had bigger valves, hardened seats, lower duration cams, and problematic carburetors. This is the head to use for turbocharged applications- since the head can be used with the original cams with the hardened valve seals and the (piston) compression is lower. The 2TGEU and 18RGEU had the reinforced heads, bigger valves, and the lowest compression (pistons). The EFI intake can be retrofitted back to carburetors.

    The Twin Cam head must only be machined by experienced machine shops. Valve service and installation is very critical. If not properly machined there will be a problem adjusting the shims, valve spring tension, and camshaft timing adjustment. The head must not be surfaced more than 1 mm or .040 in. Please read notes under Recommended Set-ups / Race configuration!

    Fuel System: The best performance can be achieved by using Fuel Injection over the carburetors. The standard Toyota ECUs are in short supply, but the most reliable set-up. For the EGU engines- the early 4AG Corolla GTS and MR2 computers can be used, since they operate within the same rpm range. Programmable Fuel Management systems will allow high compression, and radical cams- even turbo. Carburated motors will need Mikunis or Webers- if the stock Mikuni-Solex are not serviceable or to up-grade the GU carbs. For bored-out 18RGs the minimum carburetor size is at least a 44, and 40s will be sufficient for the 2TG up to 2000cc. The chokes must be changed to match the displacement. Turbocharging through carburetors is limited to about 10 psi using a fuel pressure-adjusting regulator. Do not rely on the Toyota mechanical or electric pump- use a low pressure, high volume pump.

    Ignition System: The latest generation 2TGEU and 18RGEU use a breakerless distributor. Older units can be up-graded using original Toyota distributor components from later models. Ignition amplifiers and knock sensors must be used to avoid high RPM misfires and detonation. Wire sets that have the original configuration are the best to use- they keep dirt out of the deep sparkplug pockets that may enter the block when the plugs are serviced.



    Some Recommended Set-ups:

    For Stock configuration- the early model 2TG and 18RG will give the best performance. Update the heads for unleaded fuel. This is ideal for vintage restorations. The 2TGU and 18RGU are also good, but change the carburetors and remove the exhaust air recirculating system. The 2TGEU and 18RGEU can be run with the early Toyota 4AG computers and will be excellent low maintenance fuel injection systems. Since these are high performance engines- assembly specifications are different from the regular variety Toyota single cams. Do not attempt to overhaul without the correct 2TG or 18RG manual! There have been a lot of heads and complete engines destroyed- when an important Twin Cam detail was overlooked even by "expert" Toyota mechanic. Set-up properly these engines will last a long time- like any Toyota engine.

    For Modified configuration- Prepare the head with big valves and a good port and polish job, this is the best modification that can be done. The blocks can be bored to 1750cc (2TG) and 2200cc (18RG) without changing crankshafts. The 3T crank can be used in the 2TG to give 2000cc. Avoid stroking both engines beyond these, the loss of RPM capability and inherent internal imbalance are not worth the power gain. Anytime high compression pistons are used- the cams must be replaced to avoid extremely high cylinder pressures- that will call for retarded ignition timing (and a loss of RPM and HP). The stock carburetors should be changed to at least Mikuni 44s or Weber 45s.

    For Race configuration- Treat the head to a competition port and polish with the most aggressive cams usable. You may need a custom intake manifold because stock manifolds will be the limiting factor to the port job. The big valves and dual valve springs are mandatory (they are bigger than the largest stock valves). The crankshaft and rods must be prepped- stress reliefed, heat treated, line-bored. Optionally rods may be upgraded to Carillos. Piston clearance is critical since these are high revving engines, follow the piston manufacturers tolerances. Piston valve pockets must also match the camshaft and valves used. The oil pumps in the 2TG and 18RG are different from the single cam models, try to use the original Twin Cam pumps, specially when converting to the 3T block. If available the TRD oil pumps must be used for the 2000cc 2TG. The oil pan has to baffled, specially for race and rally use. For the Full Race set-up use 320 intake and 304 cams. For the Rally set-up use 304 /288 or 304/272 cams. For the Street racer, the 304/304 set-up is very streetable and have a nice mild lobe at idle. It is very discrete! These cams cannot be used with stock pistons!! (The 288/272 cam set-up maybe used with stock pistons, as long as the head has not been cut.) Naturally adjustable gears are needed for the cams.

    The fastest 2TG set-up we have done used 330/310 cams with 1750cc pistons. The fastest 18RG used 320/304 cams with 2200cc pistons. If you need a 2-liter engine, use the 2TG (it is lighter and has slightly better Connecting Rod / Stroke geometry. The 18RG will ultimately produce more HP and torque. The Twin Cam engines will respond to tuning like real race engines. Cam timing, ignition, compression ratios, exhaust design, port profiles- all have their own advantages and disadvantages. The most popular set-ups are the 2000cc 2TG and 2200cc 18RG with all camshaft combinations. There are proprietary set-ups that may be used but try these recommendations first. Do not forget water treatment as these aluminum heads will corrode fast- and there are not enough of them left.

    If you have a RWD Toyota- these are the ultimate engines to upgrade to. All the popular cars had them as factory options! The late model 16 valves- aside from the 4AG which at one point was available in RWD, are almost impossible to convert because of they were installed at an angle, although we have conversion kits!

    Note: The 3TGTE will respond to tuning also. Since it is a turbo- all the turbo tricks will give more power than internal work- aside from the mandatory forged pistons.

  2. #2
    Senior Member Panda BVB700's Avatar
    Join Date
    Jul 2010
    Name
    Brenton
    State
    VIC
    Location
    Woodend
    Country
    Australia
    Posts
    408

    Default

    hey mate i was wondering if you know where i would be able to find alot more info on the cby stroker kit as there site is very vague with what needs to be done to the crank etc to fit these kits (machining wise) if you have any ideas it would be a great help thanks

    im realy interested in doing this but dont want to through myself in too deep once again thanks

  3. #3
    Moderator Sam-Q's Avatar
    Join Date
    Dec 2008
    Name
    Sam
    State
    VIC
    Location
    Endeavour Hills
    Country
    Australia
    Posts
    4,242

    Default

    so this is getting off topic but why not a 7a bottom end like everyone else?
    My website: SQ Engineering - 4AGE and 3SGE upgrade/replacement parts

    - SQ Engineering on facebook -

    Please e-mail to contact me instead of sending a private message on here.

  4. #4
    Senior Member Panda BVB700's Avatar
    Join Date
    Jul 2010
    Name
    Brenton
    State
    VIC
    Location
    Woodend
    Country
    Australia
    Posts
    408

    Default

    no i did have that in mind also, when i came across the BC stroker kit then another guy pointed me in the direction of CBY for there 5age kitso im pretty interested in getting some more prices on how much and also what needs doing to the block for clearance issues

Similar Threads

  1. any history on my car?
    By Tim.duncan in forum Perth & WA Events and Discussion
    Replies: 37
    Last Post: 28th August 2010, 09:41 PM
  2. A short history of Toyota variable valve timing
    By Anthony in forum Technical - Articles
    Replies: 9
    Last Post: 22nd April 2009, 08:11 PM
  3. 1989 TOYOTA COROLLA SX TWINCAM
    By EMD-RA60 in forum Cars for Sale (Toyota Only)
    Replies: 5
    Last Post: 16th June 2008, 10:56 PM
  4. Toyota Corolla Gli Twincam 16 Valve [1986]
    By Corzza in forum General Topics (No Technical Questions)
    Replies: 0
    Last Post: 18th May 2007, 06:13 PM
  5. TOYOTA CONQUEST RSi TWINCAM 16 [SERIES 2 4AGE]
    By Corzza in forum General Topics (No Technical Questions)
    Replies: 0
    Last Post: 18th May 2007, 06:05 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •