Page 8 of 27 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ... LastLast
Results 71 to 80 of 269

Thread: Tom's 4agte (in progress)

  1. #71
    Bad Email Address
    Join Date
    Dec 2008
    Posts
    708

    Default

    Mind if you source me the rebuild kit... i really want one ...
    PM me price...

  2. #72
    Senior Member
    Join Date
    Mar 2009
    Name
    Stuart
    State
    Nsw
    Location
    Sydney
    Country
    Australia
    Posts
    143

    Default

    hey mate just looking at the pics of your turbo setup. have you rotated the compressor housing on the turbo. how are you gunna mount your wastegate.

  3. #73
    Banned
    Join Date
    Oct 2009
    Posts
    1,283

    Default

    holy shit cakes...Restecp!

  4. #74
    Veteran Nikkojoe's Avatar
    Join Date
    Dec 2008
    Name
    Tom
    State
    WA
    Location
    Perth
    Country
    Australia
    Posts
    2,260

    Default

    Yeah I have rotated the exhaust housing, but havent rotated the compressor (gave up trying to remove the circlip). I still need to move it around though.

    I have 2 actuators, I probably will end up shortening the rod on one of them. There are mounts on the rear of the compressor housing (these actuators I have are not from this turbo).
    1983 AE86 ADM rust spec goodness track car build - end of the road
    1984 AE86 Silver ADM mk2 daily build - SOLD
    1984 AE86 ADM granny car daily now 4AGZE - SOLD
    1983 AE86 ADM Engine Conversion Slut - SOLD
    2002 IS200 6spd - new daily in progress
    1986 AE86 JDM GT-Apex Levin Notchback ready to roll......

  5. #75
    Senior Member
    Join Date
    Mar 2009
    Name
    Stuart
    State
    Nsw
    Location
    Sydney
    Country
    Australia
    Posts
    143

    Default

    To get the big circlip out you put the turbo a press and put some pressure down on it vertically the same way and the shaft runs but not on the shaft. Press on the housings. That should take the load off the circlip and make it easy to get out... I can take photo's if that doesn't make sense. I was thinking of doing the same thing with the waste gate actuator . There a some holes in the back that normally hold a heat shield bracket that could be used.

  6. #76
    Veteran Nikkojoe's Avatar
    Join Date
    Dec 2008
    Name
    Tom
    State
    WA
    Location
    Perth
    Country
    Australia
    Posts
    2,260

    Default

    Yeah I figured as much, but I could get the circlip if i had someone helping me

    Ill start work on it again this summer. Got a drop saw to cut my cooler pipes up neatly.
    1983 AE86 ADM rust spec goodness track car build - end of the road
    1984 AE86 Silver ADM mk2 daily build - SOLD
    1984 AE86 ADM granny car daily now 4AGZE - SOLD
    1983 AE86 ADM Engine Conversion Slut - SOLD
    2002 IS200 6spd - new daily in progress
    1986 AE86 JDM GT-Apex Levin Notchback ready to roll......

  7. #77
    Veteran Skylar's Avatar
    Join Date
    Mar 2009
    Name
    Ken
    State
    WA
    Location
    Perth
    Country
    Australia
    Posts
    1,370

    Default

    Duuuuuude

    all that's happened and no update on the fiasco?~~~

    also, I think you're going to keep the tig at your house over the summer because I don't think I'm going to be here.

  8. #78
    Veteran Nikkojoe's Avatar
    Join Date
    Dec 2008
    Name
    Tom
    State
    WA
    Location
    Perth
    Country
    Australia
    Posts
    2,260

    Default

    mmmm ok

    All that's happened? unless i just start combining other thread together, maybe

    give me a couple of weeks then i may have something
    1983 AE86 ADM rust spec goodness track car build - end of the road
    1984 AE86 Silver ADM mk2 daily build - SOLD
    1984 AE86 ADM granny car daily now 4AGZE - SOLD
    1983 AE86 ADM Engine Conversion Slut - SOLD
    2002 IS200 6spd - new daily in progress
    1986 AE86 JDM GT-Apex Levin Notchback ready to roll......

  9. #79
    Veteran Skylar's Avatar
    Join Date
    Mar 2009
    Name
    Ken
    State
    WA
    Location
    Perth
    Country
    Australia
    Posts
    1,370

    Default

    you have another thread?

    because that gearbox rebuild kit is not for this carrrrrr.

  10. #80
    Veteran Nikkojoe's Avatar
    Join Date
    Dec 2008
    Name
    Tom
    State
    WA
    Location
    Perth
    Country
    Australia
    Posts
    2,260

    Default

    did some work on it today




    Happy the way it turned out, just need to tack them all together and get them tig'd up (the bottom silicone is just there to hold it in position).

    Will do the otherside as soon as i get my new turbo
    1983 AE86 ADM rust spec goodness track car build - end of the road
    1984 AE86 Silver ADM mk2 daily build - SOLD
    1984 AE86 ADM granny car daily now 4AGZE - SOLD
    1983 AE86 ADM Engine Conversion Slut - SOLD
    2002 IS200 6spd - new daily in progress
    1986 AE86 JDM GT-Apex Levin Notchback ready to roll......

Page 8 of 27 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ... LastLast

Similar Threads

  1. 4AGE KE70, SC12 in progress
    By damo in forum KE70 / AE71 Owners Forums
    Replies: 26
    Last Post: 16th October 2009, 12:13 PM
  2. tom tom gps+ a headlight switch for 86+adm guage cluster
    By Hally in forum Car Parts For Sale
    Replies: 4
    Last Post: 25th May 2008, 10:52 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •