Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Thread: WTD: T50 + tailshaft [VIC]

  1. #1
    Veteran
    Join Date
    Dec 2008
    Name
    Rob
    State
    Victoria
    Location
    Moorabbin
    Country
    Australia
    Posts
    4,255

    Default WTD: 4ac rwd backing plate [VIC]

    So the gearbox and tailshaft seem to be sorted out now.

    I need a backing plate for a RWD 4ac or 4age to suit a T50. Anybody have one?

    thanks
    Rob




    As title states, I want a T50 with 4a bellhousing.
    (Therefore it must come from AE86 or AE71.)

    I don't want a T engine T50 that has a different output shaft spline.

    Price will depend on condition.

    I'm also after the tailshaft to go with it.
    At least the front half of the shaft.

    I'm in Melbourne South eastern suburbs but will travel within metro Melbourne to pick it up. If shipping can be done at a reasonable cost this is also fine but pickup is preferable.


    Thanks
    Rob
    Last edited by RobertoX; 23rd February 2009 at 12:59 PM.

  2. #2
    Senior Member DRFTR86's Avatar
    Join Date
    Dec 2008
    Name
    Richard
    State
    VIC
    Location
    South Oakleigh
    Country
    Australia
    Posts
    783

    Default

    ive got a tailshaft, pm me, se suburbs aswell

    PROTEK TYRE AND AUTO
    SQ ENGINEERING
    NCCE

    DRFTR86 & FATKE.....DOSEING COROLLAS SINCE 2009

  3. #3
    Veteran
    Join Date
    Dec 2008
    Name
    Aaron
    State
    TAS
    Location
    In the Mountains
    Country
    Australia
    Posts
    2,518

    Default

    need to say what diff your using buddy.

  4. #4
    Veteran
    Join Date
    Dec 2008
    Name
    Rob
    State
    Victoria
    Location
    Moorabbin
    Country
    Australia
    Posts
    4,255

    Default

    ^^ I haven't decided yet, either a t series or the standard BW...
    That is only applicable to the rear half of the tailshaft though.

    DRFTR86 I'll pm you

  5. #5
    Senior Member *E7*'s Avatar
    Join Date
    Jan 2009
    Name
    Dave
    State
    VIC
    Location
    Eastern Melb.
    Country
    Australia
    Posts
    464

    Default

    i have a good JDM t-50 in eastern suburbs.

    i don't need to get rid of it, but it's your's for the right price.

    i may also have a front tailshaft half, but i'd have to check...
    Last edited by *E7*; 21st February 2009 at 01:13 PM. Reason: add tailshaft

  6. #6
    Veteran
    Join Date
    Dec 2008
    Name
    Aaron
    State
    TAS
    Location
    In the Mountains
    Country
    Australia
    Posts
    2,518

    Default

    actually roberto its not. ae71 shaft for BW diff doesnt bolt together! for t-series diff you need front half sprinter and rear half t-18. so prob best to decide before hand

  7. #7
    Veteran shift_rook's Avatar
    Join Date
    Dec 2008
    Name
    Chris
    State
    VIC
    Location
    SE Burbs
    Country
    Australia
    Posts
    4,719

    Default

    i have a gearbox with jdm bellhousiing, it's got the t-series tailshaft and i'm in s.e suburbs, let me know mate

  8. #8
    Veteran
    Join Date
    Dec 2008
    Name
    Rob
    State
    Victoria
    Location
    Moorabbin
    Country
    Australia
    Posts
    4,255

    Default

    Ah ok, I was under the impression that they did... well since you know better, please enlighten me
    Which combination will work for the BW diff and the T50?
    I now have an ae86 tailshaft, both bits.

    My plan is to use the original ke70 diff and then switch to a t-series when I find one, maybe this wont be that easy though...

    DrifTE72 I'll PM you

  9. #9
    Senior Member *E7*'s Avatar
    Join Date
    Jan 2009
    Name
    Dave
    State
    VIC
    Location
    Eastern Melb.
    Country
    Australia
    Posts
    464

    Default

    you could use the t-18 bellhousing with the ke70 standard tailshaft to the BW diff.

    i am currently running that setup behind a 3tg/t-50 combo

    -dave

  10. #10
    Veteran
    Join Date
    Dec 2008
    Name
    Rob
    State
    Victoria
    Location
    Moorabbin
    Country
    Australia
    Posts
    4,255

    Default

    t-18 bellhousing? behind a 4a?
    Maybe a t-18 T50 with the KE tailshaft to BW diff? Using a 4a bellhousing

Page 1 of 2 1 2 LastLast

Similar Threads

  1. [VIC]Ae86 T50 And Ae86 Manual Tailshaft
    By mhmills in forum Car Parts For Sale
    Replies: 3
    Last Post: 12th December 2012, 12:01 AM
  2. Vic - 86 T series, T50 gearbox and tailshaft.
    By leigh4110 in forum Cars or Parts Wanted
    Replies: 1
    Last Post: 18th April 2012, 11:43 PM
  3. [vic] wtb ae71 parts. Pedal box, tailshaft, t50 clutch fork
    By bally in forum Cars or Parts Wanted
    Replies: 0
    Last Post: 18th November 2010, 09:46 PM
  4. [WTB] VIC: T50 Clutch Fork, AE71 Pedal Box & Tailshaft
    By bally in forum Cars or Parts Wanted
    Replies: 0
    Last Post: 15th November 2010, 11:58 PM
  5. WTD: t50, flywheel, clutch, tailshaft.
    By Nic19 in forum Cars or Parts Wanted
    Replies: 3
    Last Post: 1st April 2010, 05:23 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •