Page 1 of 3 1 2 3 LastLast
Results 1 to 10 of 23

Thread: Parts required for 4AGE in to KE70, parts only, no instructions

  1. #1
    Bad Email Address
    Join Date
    Dec 2008
    Posts
    572

    Default Parts required for 4AGE in to KE70, parts only, no instructions

    Copied,
    i can see this question being asked more than once. here is a list of the parts required to do the conversion, if i have missed anything let me know and i'll update the post (its 10:26pm and i have been at work since 4, thats 4 this morning which means i got up a 3 to get to work )


    AE86 or AE71 engine crossmember
    AE71 gearbox x member (86 one can be used)
    AE71 pedal box
    AE71 or AE86 clutch master cylinder
    AE71 or AE86 solid clutch line from master to slave, and rubber hose
    AE71 or AE86 rubber engine mounts
    AE71 or AE86 steel engine brackets
    AE71 or AE86 gearbox stays (link box to block)
    AE71 tailshaft if keeping the ke70 borg diff
    AE86 tailshaft if using S series
    AE86 tailshaft with T18 back half if using T series diff
    T50 gear box
    obviously a 4AGE of some sorts JDM being easier, ADM FWD being a little trickier but no big deal.

    thats just what you need to get the engine in there, you will also need

    modify tank pickup with fuel pump, plus mod top tank plate with a 8mm fitting for fuel feed.
    fuel hose (injection spec)

    loom to suit, either modded AE82 loom if using a bigport, modded AE92 loom if using a smallport, or a slightly less modified JDM loom again if you are using a bigport.

  2. #2
    Veteran R&D Mechanical's Avatar
    Join Date
    Dec 2008
    Name
    Davey & Riki-lee
    State
    South Australia
    Location
    Seaford SA
    Country
    Australia
    Posts
    3,003

    Default

    and what acc cable do you use if you have a ke70?

    The stock one seems to be too long, or can you still use it?>

  3. #3
    Elite rthy's Avatar
    Join Date
    Dec 2008
    Name
    Leo
    State
    VIC
    Location
    Tulla
    Country
    Australia
    Posts
    7,305

    Default

    i used a ke70 cable as the ae71 is too short (same as 4ac ae86's)
    its looped around the cmc


    also u will need the ae71 t50 crossmember (not sure if u can use the k40/50 member?)

    (AE86 on the top, ae71 bottom)

    with the cmc, holes will need to be drilled into the firewall

    more info here:


    for Auto conversions the shifter hole will need to be wider


    ae71 4ac radiator, both rad in and outlet is on the same side for the 4ac, ke70 rad will need some extention

    also since i used a fwd motor i used a electric thermo fan

    also pics of said 4a rwd engine mounts and gbox stays


    ryco Z200 universal efi fuel filter with a 4ac coil mount to look stocky

    note: it has 8mm nipples
    the stock ae71 lines fuel lines are 6mm and 4mm return

    VL Fuel pump, mounted with 4ac coil mount used lol

    would prefer intank fuel pump but this will do for now

    if you can upgrade to ae86 struts and brakes
    will need the whole ae86 struts (springs, shocks, brakes, etc...)
    use the ke70 strut top and ae86 steering arm (get jdm if u want more lock lolz)


    Wiring 4age

    Alternator


    Other links:

    Last edited by rthy; 26th December 2008 at 12:39 AM. Reason: VL
    30kw club

  4. #4
    Veteran Golberg's Avatar
    Join Date
    Dec 2008
    Name
    Lawrence
    State
    NSW
    Location
    Wollongong
    Country
    Australia
    Posts
    1,339

    Default

    I used an EP92 starlet cable, depending on the manifold though you may need to shorten the cable inner wire. The outer sheath is right on though.

  5. #5
    Senior Member
    Join Date
    Dec 2008
    Name
    Dave
    State
    SA
    Location
    The Ghetto
    Country
    Australia
    Posts
    865

    Default

    very helpful article, should make this a sticky

  6. #6
    Site Supporter matt99's Avatar
    Join Date
    Dec 2008
    Name
    Matt
    State
    VIC
    Location
    Melbourne
    Country
    Australia
    Posts
    1,365

    Default

    Gearbox stays are not really needed, but if you have them, definatly use them.

    I used an Odyssey Linear Slick BMX brake cable as my throttle cable, works well.

  7. #7
    Site Supporter Low Style's Avatar
    Join Date
    Nov 2008
    Name
    Jon
    State
    QLD
    Location
    Durack
    Country
    Australia
    Posts
    1,277

    Default

    PM slydar

    he is a wizard at 4age's

  8. #8
    Senior Member gumbie's Avatar
    Join Date
    Jan 2009
    Name
    Jordan
    State
    QLD
    Location
    Sunshine Coast
    Country
    Australia
    Posts
    605

    Default

    Quick question, Looking at gettin an AE71, 4AGE's bolt directly in correct?

  9. #9
    Veteran slydar's Avatar
    Join Date
    Nov 2008
    Name
    Dimitri
    State
    QLD
    Location
    Brisbane
    Country
    Australia
    Posts
    3,096

    Default

    yeah. the engine will mount using the stock mounts and transmission. 20v will need the dizzy moved or the firewall clearenced.

  10. #10
    Veteran
    Join Date
    Dec 2008
    Name
    Aaron
    State
    TAS
    Location
    In the Mountains
    Country
    Australia
    Posts
    2,518

    Default

    you should really use a surge tank or get a jdm fuel tank or you will get fuel surge when the tank is low going around roundabout/thrashing etc.

    for this you require a small low pressure lift pump to fill the surge tank then a main EFI pump (VL etc) to pump from surge to engine.
    Last edited by ae71; 2nd February 2009 at 11:37 AM.

Page 1 of 3 1 2 3 LastLast

Similar Threads

  1. clearing all corolla ae71/ke70/ae86 parts also 4age parts
    By tuff te-72 in forum Car Parts For Sale
    Replies: 7
    Last Post: 26th May 2011, 01:08 PM
  2. 4age smallport parts and ke70 conversion parts
    By ionise in forum Cars or Parts Wanted
    Replies: 0
    Last Post: 10th September 2010, 08:33 PM
  3. Replies: 5
    Last Post: 17th May 2010, 02:23 PM
  4. Parts required for 4AGE in to KE70
    By Gilly in forum Technical - Articles
    Replies: 27
    Last Post: 2nd October 2008, 12:42 AM
  5. Medwin's Parts Required Thread
    By medwin46 in forum Cars or Parts Wanted
    Replies: 30
    Last Post: 21st November 2007, 10:55 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •