Page 3 of 4 FirstFirst 1 2 3 4 LastLast
Results 21 to 30 of 34

Thread: engine installation

  1. #21
    Senior Member koulouris#03's Avatar
    Join Date
    Dec 2008
    Name
    John
    State
    Nsw
    Location
    EarlwoodNsw
    Country
    Au
    Posts
    167

    Default

    i currently have to hachis. one with a very nice body and interior, and the other with an excelent motor and running gear, but shit body.
    i want to put the motor, brakes, suspension, and all other goodies from shit body sprinter into good body sprinter.

    the good body sprinter is a stock aus spec hachi. 4ac.

    im not sure of what parts i will need. i would assume not many, cause they are already in one complete car.

    this is all the info i have.

  2. #22
    Senior Member
    Join Date
    Dec 2008
    Name
    Reeece
    State
    NSW
    Location
    Casula
    Country
    Australia
    Posts
    688

    Default

    transfer all the fuel lines..over for starters and swap tanks if its a jdm in shitty sprinter.. You wanna sell any parts from the shitty sprinter

  3. #23
    Senior Member koulouris#03's Avatar
    Join Date
    Dec 2008
    Name
    John
    State
    Nsw
    Location
    EarlwoodNsw
    Country
    Au
    Posts
    167

    Default

    once i have done the swap, i will be selling all the left overs. at this point i dont know what im gonna need and not need from each hachi.

  4. #24
    Senior Member Medwin_3sGTE_AE86's Avatar
    Join Date
    Dec 2008
    Name
    Bendyaumum
    State
    TAS
    Location
    Southern
    Country
    Australia
    Posts
    421

    Default

    Let me get this straight....

    - You have 2x Sprinters. 1x of which has the 'mad' engine and good running gear but shitty body, the other has shit running gear but good body. Correct?

    - You wish to put all the running gear from the shitty bodied car into the good one? Yes?

    - You were quoted $6k for a simple swap over job? Someone is trying to take you to the cleaners...

    Have a crack at it mate. If the shitty bodied car is running, its only a matter of swapping everything over (wiring etc too) and it'll be fine. $6k is a bit outrageous if what i've listed above are infact the circumstances.

    However, there is a fair bit of work (hours wise) in swapping it all over, hence the excessive quote. I am with most others on this one, attempt it yourself. If it looks like a 'Shit, am i gonna remember how that went' situation, take photos of it and draw diagrams etc, its not that hard!

  5. #25

    Default

    +1 on that !

  6. #26
    Veteran Golberg's Avatar
    Join Date
    Dec 2008
    Name
    Lawrence
    State
    NSW
    Location
    Wollongong
    Country
    Australia
    Posts
    1,339

    Default

    How about I do all the work for you, and keep the shitty bodied AE86 afterwards, no charges?

    Do know if that's honestly fair, but I'd do it, have plenty of time at the moment.

  7. #27
    Senior Member koulouris#03's Avatar
    Join Date
    Dec 2008
    Name
    John
    State
    Nsw
    Location
    EarlwoodNsw
    Country
    Au
    Posts
    167

    Default


    hey bud. if you are serious about your offer, i would be keen. and would even throw in a set of aw11 mr2 seats. hit me up, if your keen.


    i would be looking at doing the engine swap myself, but dont have a garage.
    Last edited by koulouris#03; 7th January 2009 at 10:28 PM.

  8. #28
    Veteran Golberg's Avatar
    Join Date
    Dec 2008
    Name
    Lawrence
    State
    NSW
    Location
    Wollongong
    Country
    Australia
    Posts
    1,339

    Default

    You have a PM

  9. #29
    Veteran Rice86's Avatar
    Join Date
    Jan 2009
    Name
    Richard
    State
    NSW
    Location
    Liverpool
    Country
    Australia
    Posts
    1,853

    Default

    so is the car just a rolling shell?...

    you can always make it cheaper by taking the current engine out, dropping the new engine in on your own...do what takes no brain to do, that will save people charging u with labour, then with stuff you know u cant do, u pay people

  10. #30
    Senior Member
    Join Date
    Dec 2008
    Posts
    259

    Default

    You talked to John Bates (Sprinterman68) already ?

    It might sound like a bit... but if you want to get it done right the first time and dont have time/resources to DIY.. then John is your man.
    Probably the best AE86 guy there is. People swear by his work.

Page 3 of 4 FirstFirst 1 2 3 4 LastLast

Similar Threads

  1. Coilover Installation
    By Ham86 in forum Technical - Questions
    Replies: 13
    Last Post: 7th July 2011, 09:54 PM
  2. New ECU installation
    By sdrawkcab in forum Technical - Questions
    Replies: 5
    Last Post: 12th December 2009, 12:14 AM
  3. 4ac head installation
    By slippry in forum Technical - Questions
    Replies: 4
    Last Post: 5th November 2007, 04:05 PM
  4. Costs for engine installation
    By haydenzz in forum General Topics (No Technical Questions)
    Replies: 10
    Last Post: 28th September 2007, 05:08 PM
  5. cam installation
    By slippry in forum Technical - Questions
    Replies: 10
    Last Post: 12th August 2007, 09:56 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •