Page 6 of 10 FirstFirst 1 2 3 4 5 6 7 8 9 10 LastLast
Results 51 to 60 of 97

Thread: W5X series Gear boxs in an ae86. Costly?

  1. #51
    Senior Member --Redwork--'s Avatar
    Join Date
    Jan 2009
    Name
    Jason
    State
    QLD
    Location
    Nundah
    Country
    Australia
    Posts
    954

    Default

    I'm assuming that price is GBP.. if so works out to be $500...

  2. #52
    Senior Member DR86FT's Avatar
    Join Date
    Jan 2009
    Name
    Kaan
    State
    QLD
    Location
    Emerald
    Country
    Australia
    Posts
    595

    Default

    i got my dellow bellhousing already and the yoke hangs over the back ? does yours?

  3. #53
    Moderator Sam-Q's Avatar
    Join Date
    Dec 2008
    Name
    Sam
    State
    VIC
    Location
    Endeavour Hills
    Country
    Australia
    Posts
    4,242

    Default

    I am feeling generous, I will put my W55 out later today and take a picture of it next to my spare T50
    My website: SQ Engineering - 4AGE and 3SGE upgrade/replacement parts

    - SQ Engineering on facebook -

    Please e-mail to contact me instead of sending a private message on here.

  4. #54
    Senior Member DR86FT's Avatar
    Join Date
    Jan 2009
    Name
    Kaan
    State
    QLD
    Location
    Emerald
    Country
    Australia
    Posts
    595

    Default

    thank you

  5. #55
    Moderator Sam-Q's Avatar
    Join Date
    Dec 2008
    Name
    Sam
    State
    VIC
    Location
    Endeavour Hills
    Country
    Australia
    Posts
    4,242

    Default

    I took the pic 2 days ago, I need to get my camera out later and upload a pic, just a preview- I was wrong, looks like I got to correct myself.
    My website: SQ Engineering - 4AGE and 3SGE upgrade/replacement parts

    - SQ Engineering on facebook -

    Please e-mail to contact me instead of sending a private message on here.

  6. #56
    Moderator Sam-Q's Avatar
    Join Date
    Dec 2008
    Name
    Sam
    State
    VIC
    Location
    Endeavour Hills
    Country
    Australia
    Posts
    4,242

    Default




    I lined them up so the edge of the shaft ends where even. As it can be seen the W55 shifter is one position further back, and a shifter that was straight up instead would be more ideal.

    I also dread cleaning that T50 for obvious reasons
    My website: SQ Engineering - 4AGE and 3SGE upgrade/replacement parts

    - SQ Engineering on facebook -

    Please e-mail to contact me instead of sending a private message on here.

  7. #57
    Veteran NIZLAH's Avatar
    Join Date
    Dec 2008
    Name
    Niz
    State
    QLD
    Location
    South~Slide Briz
    Country
    Australia
    Posts
    1,077

    Default

    I did have pics of my W55 with niteparts b/housing next to a T50 with b/housing but they were lost when my hard drive fried itself... anyhow it was much more even from memory than what you posted Sam... they were practically identical length/shifter position etc give/take a cm or 2.. Interesting
    ------------------>>>Need something welded locally??? Hit me up, I may just be able to help<<<------------------

    BENT MECHANIX - Garage 20:

  8. #58
    Moderator Sam-Q's Avatar
    Join Date
    Dec 2008
    Name
    Sam
    State
    VIC
    Location
    Endeavour Hills
    Country
    Australia
    Posts
    4,242

    Default

    was it the straight up shifter design or like what I have here? do you remember?
    My website: SQ Engineering - 4AGE and 3SGE upgrade/replacement parts

    - SQ Engineering on facebook -

    Please e-mail to contact me instead of sending a private message on here.

  9. #59
    Veteran NIZLAH's Avatar
    Join Date
    Dec 2008
    Name
    Niz
    State
    QLD
    Location
    South~Slide Briz
    Country
    Australia
    Posts
    1,077

    Default

    shifter looks to be the same as what you posted.... sits in pretty much the same position as my T50 shifter did inside the car.... I could be wrong but yours looks like its a couple of cms longer (the g/box {in length}) its a little hard to tell with the shifter boots covering the ends
    ------------------>>>Need something welded locally??? Hit me up, I may just be able to help<<<------------------

    BENT MECHANIX - Garage 20:

  10. #60
    Senior Member DR86FT's Avatar
    Join Date
    Jan 2009
    Name
    Kaan
    State
    QLD
    Location
    Emerald
    Country
    Australia
    Posts
    595

    Default

    can u measure the bellhousing? would that matter just wanna see if my dellow one is the right size.
    also do u have spares for w55 mine was missing alot of stuff. I need a reverse switch, speedo gear, shifter and i wanna move the shifter to the same position as the t50.

    thanks

Page 6 of 10 FirstFirst 1 2 3 4 5 6 7 8 9 10 LastLast

Similar Threads

  1. Replies: 9
    Last Post: 25th February 2012, 06:08 PM
  2. Wtb: w5x to f series tailshaft or parts
    By DR86FT in forum Cars or Parts Wanted
    Replies: 19
    Last Post: 21st August 2011, 09:15 PM
  3. WTB: W5X to G block manual bellhousing and gear
    By xsoarerx in forum Cars or Parts Wanted
    Replies: 4
    Last Post: 22nd February 2008, 12:09 AM
  4. 4a/w5x bellhousing and toda cam gear Q's
    By desam8 in forum Technical - Questions
    Replies: 8
    Last Post: 26th January 2007, 11:10 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •