Page 18 of 18 FirstFirst ... 8 9 10 11 12 13 14 15 16 17 18
Results 171 to 174 of 174

Thread: 4AGE cams......choices, dyno results and discussions!!!

  1. #171
    Senior Member Futo_gt86's Avatar
    Join Date
    Mar 2011
    Name
    Ali
    State
    QLD
    Location
    4300
    Country
    Australia
    Posts
    680

    Default


    TO REMOVE ADS, PLEASE
    REGISTER OR SIGN IN
    Quote Originally Posted by bunki86 View Post
    Unless ya have big lift or turning ya motor to 9k. I wouldn't waste money on them toda under bucket shims. Then you have to pay some one to set them up. If they dont supply the right shims, then they have to grind valve stems.
    i just built a motor with them and i think he wasted money on that toda setup when the money could have been better spent else where.
    uprated springs for sure. Ya running boost now so boost on the back of the valve is going to counter seat pressure.
    Toda uprated 16V springs are cheap enough, i'll get some happening.
    Does the GZE run a different spring to a GE, or no?

  • #172
    Senior Member
    Join Date
    Mar 2013
    Name
    andrew
    State
    WA
    Location
    perth
    Country
    australia
    Posts
    149

    Default

    in stock form, i dont know. but aftermarket 4a 16v springs will with both.

  • #173
    Junior Member
    Join Date
    Oct 2016
    Name
    luke
    State
    somerset
    Location
    wellington
    Country
    United Kingdom
    Posts
    1

    Default

    Hi im new to this site iv got a 1984 trueno booter 1.6 4age and ive come across this thread and am in need of advice !

    im fitting a 272 deg cam to my 86 and ive got the following parts
    cam belt
    water pump
    steam seals
    x2 camshafts
    pulleys
    gasket kit
    head bolts

    my cams are going to give me 8.1mm of lift will i need to change my shims ?
    i dont want to start the job and become stuck and not have all the parts i need !
    also can i install them and leave the timming relatively oem so i can get it rolling roaded / tuned ?

    thank you in advance

  • #174
    Senior Member Slimer86's Avatar
    Join Date
    Dec 2008
    Name
    Marco
    State
    SA
    Location
    North Adelaide Suburbs
    Country
    Australia
    Posts
    764

    Default


    TO REMOVE ADS, PLEASE
    REGISTER OR SIGN IN
    Changing cams requires the clearances be checked and adjusted. You will need to make adjustments. Measure all shims as they are in position. May get lucky and just swap positions. Look on club4ag I think the thread was written by assasin86
    Big up's for the North East Massiv'
    NSATB - New Skids Around The Block

  • Page 18 of 18 FirstFirst ... 8 9 10 11 12 13 14 15 16 17 18

    Similar Threads

    1. 4AGE Team Toyota Australia dyno runs
      By Frak in forum Technical - Articles
      Replies: 89
      Last Post: 3rd September 2013, 02:08 PM
    2. Looking for stock dyno results of 4age's(16v)
      By odessy in forum Technical - Questions
      Replies: 7
      Last Post: 15th June 2010, 07:24 PM
    3. ECU Choices
      By oni in forum Technical - Questions
      Replies: 3
      Last Post: 18th August 2008, 07:37 PM

    Tags for this Thread

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •