Page 8 of 33 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ... LastLast
Results 71 to 80 of 330

Thread: What did you do on your ae/ke today thread

  1. #71
    Moderator dove grey 64's Avatar
    Join Date
    Aug 2010
    Name
    Geoff
    State
    VIC
    Location
    mt dandenong
    Country
    Australia
    Posts
    2,437

    Default

    ok, i was under the impression if i chuck one on it would kill the bearings quickly? am i thinking of the wrong thing? i'd really just rather try getting my setup to work the way it should. was working fine before but started to play up in the last week or so.
    also on the subject of vac lines, one goes to the charcoal canister and where does the other one go?
    if i block the other one the car stalls, if i leave it open my rev's sit at 1500 at idle and occasionally it hunts for idle (has unknown cams) so i got a t piece and plugged it in with the line running to the charcoal can and rev's sat nice at 1000 idle, after a week it started to hunt at idle from 500 to 1000 and then started to stall.
    my twin thermo's have been stuck on and it draws alot of amps so that why i think it stalls, also have tried to loop a small bit of line on the two but that doesnt work, well it did work but then at idle when my thermo's come on it would stall. argh

  2. #72
    Moderator dove grey 64's Avatar
    Join Date
    Aug 2010
    Name
    Geoff
    State
    VIC
    Location
    mt dandenong
    Country
    Australia
    Posts
    2,437

    Default

    hah fixed itself today, must have been an old thermo switch that decided to play ball again. sweet. there are two types, one that looks all smooth and one likes like it has a bearing at the end, i fitted the bearing type i scored at pick a part, guess it needed running in to get working again

  3. #73
    Senior Member
    Join Date
    Mar 2010
    Name
    Drew
    State
    VIC
    Location
    Lilydale
    Country
    Australia
    Posts
    492

    Default

    toyotas have self heal!

    i lost and oil cap last night, does anyone have a 4 ac or 4k one lying around with the jap writing on top, will give wristys

  4. #74
    Elite rthy's Avatar
    Join Date
    Dec 2008
    Name
    Leo
    State
    VIC
    Location
    Tulla
    Country
    Australia
    Posts
    7,305

    Default

    fyi the fwd water pump will crack with a clutch fan stuck on it, its happened to me... 3 times
    30kw club

  5. #75
    Senior Member Panda BVB700's Avatar
    Join Date
    Jul 2010
    Name
    Brenton
    State
    VIC
    Location
    Woodend
    Country
    Australia
    Posts
    408

    Default

    started it up got it to operating temp and tried to find out what is going on with it with very little success
    adm ae86 now one hell of a project
    ae71 small project

  6. #76
    Senior Member Gear-head's Avatar
    Join Date
    Jul 2010
    Name
    James
    State
    ViC
    Location
    A place near you
    Country
    Australia
    Posts
    215

    Default

    Drove for 2 hrs from the west side to center rd wreckers to get xt130 hubs and took me all up 4 hrs to just get 2 hubs. Cost me $56 and now I got to buy bearings for them. And clean them up before I fit them on

  7. #77
    Moderator dove grey 64's Avatar
    Join Date
    Aug 2010
    Name
    Geoff
    State
    VIC
    Location
    mt dandenong
    Country
    Australia
    Posts
    2,437

    Default

    found out in yesterdays heat wave my clutch fluid is getting too hot, replacement clutch line i got sits out closer to my exhaust. thinking of getting a flex line with a 45 deg bango fitting.
    was sitting in traffic and wouldnt let me select 1st or 2nd, had to turn off the motor and engage 1st then start up again. argh lol
    but then by the time i got back to the hills with cooler air the problem went away, didnt have the issue today either. hot clutch fluid?

  8. #78
    Veteran Jimmee1990's Avatar
    Join Date
    Mar 2011
    Name
    James
    State
    VIC
    Location
    Mt Dandenong
    Country
    Australia
    Posts
    1,132

    Default

    Fitted up my brand new kouki trueno bumper, and changed my alignment around a bit.

  9. #79
    Veteran hachi_dk's Avatar
    Join Date
    Mar 2009
    Name
    Filip
    State
    VIC
    Location
    Jozzaville
    Country
    Australia
    Posts
    1,069

    Default

    vacuumed and washed my 86 and jzx100

  10. #80
    Token Member regginblack's Avatar
    Join Date
    Apr 2009
    Name
    reggin
    State
    VIC
    Location
    western suburbs
    Country
    Australia
    Posts
    348

    Default

    Your such a freaking boss. I want a chaser so bad!!

Page 8 of 33 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ... LastLast

Similar Threads

  1. Universal 3sge (inc Beams) into AE/KE thread
    By Sam-Q in forum Technical - Questions
    Replies: 399
    Last Post: 21st June 2017, 04:10 PM
  2. KE/AE Bits
    By chrisjjanfd3s in forum Car Parts For Sale
    Replies: 22
    Last Post: 19th September 2012, 04:25 PM
  3. AE/KE Parts must go!
    By Low Style in forum Car Parts For Sale
    Replies: 6
    Last Post: 2nd November 2011, 06:08 PM
  4. 4age into ae/ke
    By haveaparty in forum Technical - Articles
    Replies: 2
    Last Post: 8th March 2011, 07:56 AM
  5. ke or ae
    By emmyy3 in forum General Topics (No Technical Questions)
    Replies: 31
    Last Post: 9th September 2008, 06:52 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •