Page 1 of 2 1 2 LastLast
Results 1 to 10 of 13

Thread: Blacktop 20v excessive fueling - Video Attached

  1. #1
    Noooob
    Join Date
    Jun 2010
    Name
    Matt
    State
    NSW
    Location
    Campbelltown
    Country
    Australia
    Posts
    5,246

    Default Blacktop 20v excessive fueling - Video Attached

    Car

    Ae82 sedan with blacktop 20v (yep the motor faces the wrong way)

    Problem

    The car is running on 3 cyclinders, appears to be cyclinder 1 that has a problem with being over fueled.

    The video attached is after being switched off for around 30 seconds, it just bubbles up and over flows out the top of the spark plug. Cyclinders 2-4 you can clearly see the top of the pistons and they are dry.

    I've tried swapping the fuel pressure reg and cranking for about a minute to remove excess fuel from the cyclinders after swapping the pressure reg.

    Compression is between 210 and 215 across all cyclinders. And no signs of oil in the water or water in the oil (is a bit of extra fuel though)

    After starting to write this, thinking i might try swapping injectors 1 and 3 to see if the problem remains with cyclinder 1. Will get back to you on this, but if anyone else has had this problem or knows where to start that would be great.

    Happening since

    I've had this car for about 6 months and haven't done anything with it, other than start it up from time to time and let run for a couple of minutes and shut it down. Its always ran a bit shit, but i put in new plugs a while back and it seamed to be better.

    I rewired it about a two months ago as the original guy who wired it believed twisting wires and taping it up was good enough.. I doubt it is the wiring as i've wired up around 20 of these in FWD format now...



    Thanks for your help guys.
    Last edited by Matt; 27th November 2011 at 02:29 PM.

  2. #2
    Junior Member
    Join Date
    Feb 2011
    Name
    stewart
    State
    QLD
    Location
    Sunnybank
    Country
    Australia
    Posts
    12

    Default

    that's an alot of fuel, hope you haven't hydraulic locked it. let us know how swapping the injector goes.

  3. #3
    Noooob
    Join Date
    Jun 2010
    Name
    Matt
    State
    NSW
    Location
    Campbelltown
    Country
    Australia
    Posts
    5,246

    Default

    When removing the injector the rubber seal at the bottom was snapped in half, so i replaced the injector with one from another engine.

    After starting it up again , the first minute or so it was still smoking outta the exhaust, but as it was holding idle and running ok i ran it up to temp.

    Pretty sure the engine is fine, just had a little bath in fuel.
    Last edited by Matt; 27th November 2011 at 09:05 PM.

  4. #4
    Moderator Sam-Q's Avatar
    Join Date
    Dec 2008
    Name
    Sam
    State
    VIC
    Location
    Endeavour Hills
    Country
    Australia
    Posts
    4,242

    Default

    so a stuck open injector then?
    My website: SQ Engineering - 4AGE and 3SGE upgrade/replacement parts

    - SQ Engineering on facebook -

    Please e-mail to contact me instead of sending a private message on here.

  5. #5
    Noooob
    Join Date
    Jun 2010
    Name
    Matt
    State
    NSW
    Location
    Campbelltown
    Country
    Australia
    Posts
    5,246

    Default

    yeah pretty much... Dunno if it was the seal or stuck open

  6. #6
    Forum Sponsor TODA AU's Avatar
    Join Date
    Feb 2011
    Name
    Adrian
    State
    NSW
    Location
    Thornleigh
    Country
    Australia
    Posts
    101

    Default

    If the lower seal on a side feed injector fail, it'll fill the cylinder.

  7. #7
    Noooob
    Join Date
    Jun 2010
    Name
    Matt
    State
    NSW
    Location
    Campbelltown
    Country
    Australia
    Posts
    5,246

    Default

    Going to swap them on all my engines, may assist a little with running rich...

    Anyone know where i can get say 30 of them cheap?

  8. #8
    Moderator Sam-Q's Avatar
    Join Date
    Dec 2008
    Name
    Sam
    State
    VIC
    Location
    Endeavour Hills
    Country
    Australia
    Posts
    4,242

    Default

    ah yes of course, I got mixed up with top feed which wouldn't make that much of a difference.


    Matt: 30 of what? injectors??? or seals?
    My website: SQ Engineering - 4AGE and 3SGE upgrade/replacement parts

    - SQ Engineering on facebook -

    Please e-mail to contact me instead of sending a private message on here.

  9. #9
    Noooob
    Join Date
    Jun 2010
    Name
    Matt
    State
    NSW
    Location
    Campbelltown
    Country
    Australia
    Posts
    5,246

    Default

    Seals gotta do friends cars I've built too

  10. #10
    Moderator Sam-Q's Avatar
    Join Date
    Dec 2008
    Name
    Sam
    State
    VIC
    Location
    Endeavour Hills
    Country
    Australia
    Posts
    4,242

    Default

    I can get them, I will find out what their worth as I might as well offer them on my site
    My website: SQ Engineering - 4AGE and 3SGE upgrade/replacement parts

    - SQ Engineering on facebook -

    Please e-mail to contact me instead of sending a private message on here.

Page 1 of 2 1 2 LastLast

Similar Threads

  1. Replies: 2
    Last Post: 21st July 2012, 02:00 PM
  2. Replies: 0
    Last Post: 29th January 2012, 04:29 PM
  3. need help s/t 20v over fueling poor ventilation setup
    By ae8620v in forum Technical - Questions
    Replies: 6
    Last Post: 16th June 2011, 01:14 PM
  4. > Fueling Problem
    By jason in forum Technical - Questions
    Replies: 4
    Last Post: 20th January 2007, 10:26 AM
  5. silvertop 20v or blacktop 20v
    By Cj_sullivan in forum General Topics (No Technical Questions)
    Replies: 7
    Last Post: 6th September 2006, 12:42 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •