Page 10 of 50 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ... LastLast
Results 91 to 100 of 495

Thread: 2AZ powered 86

  1. #91
    Veteran LittleRedSpirit's Avatar
    Join Date
    Dec 2008
    Name
    Matt
    State
    QLD
    Location
    West
    Country
    Australia
    Posts
    1,863

    Default


    TO REMOVE ADS, PLEASE
    REGISTER OR SIGN IN
    Going to the workshop to do some more odd jobs on it today.

    I will finally fit the diff baffles and polish inside the manifold.

    Then the only things left on the mechanical package are the wiring and tune, tailshaft, and cutting away the new block for the starter motor clearance and tapping one hole for the BH union like the dummy motor. Oh and I need to make a vaccum manifold thats designed to spread the idle control air evenly between each cylinder. I have a design in mind but I need to fabricate it. Just basically a funnel shaped unit with the 4 nipples at the broad end and the idle controller feeding them at equal spacing from the narrow end, if you can picture it. Just deciding whether PVC will be high temp enough. Probably not, I want to bolt it to the inlet side under the manifold.

    Then its all just bodywork. One small tweak of the tunnel, fit the coilovers, n diff. Flare to suit some wheels. Then paint it and I can just build it like a man possessed.

    I might also invest in some tension control rods and steering knuckles from TTT at some stage.






  • #92
    Veteran LittleRedSpirit's Avatar
    Join Date
    Dec 2008
    Name
    Matt
    State
    QLD
    Location
    West
    Country
    Australia
    Posts
    1,863

    Default

    Polishing came up a treat.



    Also faced the oil extender flanges.






  • #93
    Veteran NIZLAH's Avatar
    Join Date
    Dec 2008
    Name
    Niz
    State
    QLD
    Location
    South~Slide Briz
    Country
    Australia
    Posts
    1,077

    Default

    where did you get that faced/cost?
    I need to do the same to my top rad outlet, atm it has a homemade thick rubber gasket to stop it leaking, but I don't think it will suffice for very long..
    ------------------>>>Need something welded locally??? Hit me up, I may just be able to help<<<------------------

    BENT MECHANIX - Garage 20:

  • #94
    Veteran LittleRedSpirit's Avatar
    Join Date
    Dec 2008
    Name
    Matt
    State
    QLD
    Location
    West
    Country
    Australia
    Posts
    1,863

    Default

    Did it myself on my disc sander wheel.

    Just bring it over. Or is it on your car?
    Last edited by LittleRedSpirit; 1st January 2013 at 12:40 PM.






  • #95
    Veteran NIZLAH's Avatar
    Join Date
    Dec 2008
    Name
    Niz
    State
    QLD
    Location
    South~Slide Briz
    Country
    Australia
    Posts
    1,077

    Default

    ah nice, yeh its on the 86... can pull it off there though, not like the engine is going to be run... bit of a dick around to remove but it must be done I guess... you gonna be there sat arvo? its quite warped, reckon its cable of grinding it down flat?
    ------------------>>>Need something welded locally??? Hit me up, I may just be able to help<<<------------------

    BENT MECHANIX - Garage 20:

  • #96
    Veteran LittleRedSpirit's Avatar
    Join Date
    Dec 2008
    Name
    Matt
    State
    QLD
    Location
    West
    Country
    Australia
    Posts
    1,863

    Default

    Yeah its a 12 inch disc so that should be plenty large to flatten a thermo housing.






  • #97
    Veteran NIZLAH's Avatar
    Join Date
    Dec 2008
    Name
    Niz
    State
    QLD
    Location
    South~Slide Briz
    Country
    Australia
    Posts
    1,077

    Default

    its steel though not alloy, is it capable of tackling that?
    ------------------>>>Need something welded locally??? Hit me up, I may just be able to help<<<------------------

    BENT MECHANIX - Garage 20:

  • #98
    Veteran LittleRedSpirit's Avatar
    Join Date
    Dec 2008
    Name
    Matt
    State
    QLD
    Location
    West
    Country
    Australia
    Posts
    1,863

    Default

    Yep.

    The pipe above is mild steel.






  • #99
    Veteran NIZLAH's Avatar
    Join Date
    Dec 2008
    Name
    Niz
    State
    QLD
    Location
    South~Slide Briz
    Country
    Australia
    Posts
    1,077

    Default

    sweet, was thinking it looked like steel... you gonna be about on sat arvo?
    ------------------>>>Need something welded locally??? Hit me up, I may just be able to help<<<------------------

    BENT MECHANIX - Garage 20:

  • #100
    Veteran LittleRedSpirit's Avatar
    Join Date
    Dec 2008
    Name
    Matt
    State
    QLD
    Location
    West
    Country
    Australia
    Posts
    1,863

    Default


    TO REMOVE ADS, PLEASE
    REGISTER OR SIGN IN
    Just give me a call, probably.






  • Page 10 of 50 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ... LastLast

    Similar Threads

    1. The 4age powered Toyota 86
      By Matt in forum Info / Pics & Discussion
      Replies: 5
      Last Post: 18th December 2012, 11:36 AM
    2. 2AZ COP's - JJR recliner - rear shocks
      By biggo in forum Car Parts For Sale
      Replies: 0
      Last Post: 11th August 2012, 11:15 AM
    3. WTB: coilpacks + plugs off 1NZ, 2AZ or 1ZZ
      By Sam-Q in forum Cars or Parts Wanted
      Replies: 16
      Last Post: 15th February 2009, 08:09 PM
    4. 13b/13bT powered 86's?
      By jarryd in forum Technical - Questions
      Replies: 20
      Last Post: 30th November 2007, 01:01 AM
    5. Calling all CA18DET powered 86's
      By lowau in forum General Topics (No Technical Questions)
      Replies: 27
      Last Post: 21st August 2006, 11:06 AM

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •