Page 2 of 3 FirstFirst 1 2 3 LastLast
Results 11 to 20 of 26

Thread: LS1 KE70.. does anyone have any info or build pics of this car.??

  1. #11
    Senior Member Hen may possibly be a nut's Avatar
    Join Date
    Jan 2009
    Name
    Hen
    State
    Victoria
    Location
    Mt Macedon
    Country
    Australia
    Posts
    909

    Default

    Castlemaine rod shop, not Castle Hill.

  2. #12
    Senior Member --Redwork--'s Avatar
    Join Date
    Jan 2009
    Name
    Jason
    State
    QLD
    Location
    Nundah
    Country
    Australia
    Posts
    954

    Default

    LOL.. yeah I still couldn't find it on there website
    Just found it.. it's still 1k though..

  3. #13
    Senior Member J0RD0's Avatar
    Join Date
    Feb 2010
    Name
    Jordan
    State
    QLD
    Location
    Brisbane
    Country
    Australia
    Posts
    369

    Default

    so what are you up to red?? who's doing what in what car?
    THE EVOROLLA none of this SR shit . . . EVO 7 powered bitches

    https://www.facebook.com/KeConversions

    KE conversions - making your conversion simple

    4AGE CA18 SR20 BEAMS 1UZ to KEXX mounting kits and hydraulic pedal box's available

  4. #14
    Senior Member dangdang's Avatar
    Join Date
    Aug 2010
    Name
    Danga
    State
    Tas
    Location
    Hobart
    Country
    Aus
    Posts
    151

    Default

    Don't be shy and just chaff it back through the firewall a little bit...plenty of clearance then





    Last edited by dangdang; 22nd October 2012 at 10:43 PM.

  5. #15
    Senior Member --Redwork--'s Avatar
    Join Date
    Jan 2009
    Name
    Jason
    State
    QLD
    Location
    Nundah
    Country
    Australia
    Posts
    954

    Default

    Its not fitting the engine that I'm concernd about.. its trying to get hald descent headers down the drivers side past the steering colomn..

    This is how my car sits currently.. Except it has less firewall than in this pic..

  6. #16
    Senior Member --Redwork--'s Avatar
    Join Date
    Jan 2009
    Name
    Jason
    State
    QLD
    Location
    Nundah
    Country
    Australia
    Posts
    954

    Default

    dangdang..

    Any more pictures.??
    You going to convert to rear sump.?
    Thats roughly about where I think my engine will end up.
    You almost need to convert to the center shift possition with the box where it is...

  7. #17
    Veteran johl's Avatar
    Join Date
    Dec 2008
    Name
    Johl
    State
    QLD
    Location
    Brisbane
    Country
    Australia
    Posts
    2,812

    Default

    are you putting the new chassis rails inside the car instead of below it red?
    stroked 2L ca18-ae86 in the build...eta xmas 2012?

  8. #18
    Senior Member --Redwork--'s Avatar
    Join Date
    Jan 2009
    Name
    Jason
    State
    QLD
    Location
    Nundah
    Country
    Australia
    Posts
    954

    Default

    Yeah.. In line with the sills so it can be one the ground.
    Stupid stock rails hang down like 40mm.. and there's stuff all room for exhaust either with stock floor pan..
    Also changing to a 3 link rear suspension..

  9. #19
    Senior Member Deeken's Avatar
    Join Date
    Jan 2011
    Name
    Deeken
    State
    NSW
    Location
    Port Macquarie
    Country
    Australia
    Posts
    193

    Default

    Damn it, was keen on getting stuck into an ls1 conversion into my ae71 until i read this thread.. I seen an ls1 s13 and the headers they had seemed to fit around the outside of their steering shaft..

    I was hoping there was some model of header that would clear the shaft..

    And also, where does the shifter end up if you sit the engine back as far as those pictures, if that is the original handbrake location, I'd say that wouldnt be too uncomfortable and could just run a hydro.

  10. #20
    Senior Member --Redwork--'s Avatar
    Join Date
    Jan 2009
    Name
    Jason
    State
    QLD
    Location
    Nundah
    Country
    Australia
    Posts
    954

    Default

    You can get a center shift setup for T68 so the level comes out alot farther forward. Where the other inspection plate bolts on with the 4 bolts in the picture..

Page 2 of 3 FirstFirst 1 2 3 LastLast

Similar Threads

  1. Dave's KE70 budget track car build
    By lildavo in forum KE70 / AE71 Owners Forums
    Replies: 6
    Last Post: 16th April 2012, 12:43 AM
  2. KE70 Drift/Track Car Build.
    By luke641 in forum KE70 / AE71 Owners Forums
    Replies: 38
    Last Post: 19th March 2012, 06:50 PM
  3. VZ Police Pack LS1 Own the car that used to chase you!
    By Brendan in forum Cars for Sale (Not Toyotas)
    Replies: 2
    Last Post: 20th October 2010, 05:41 PM
  4. looking for pics/info of the drift battle magazine ae86
    By DRFTR86 in forum Offtopic Discussions
    Replies: 26
    Last Post: 17th February 2009, 08:51 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •