KE70 Sedan - Sleeper looks with all the goods QLD (Bris)

[Futo_gt86]

I needs to sell my KE70 Sedan to fund Pano build, so, sadly this has to go.

BODY/EXTERIOR:
Quad light conversion
MK1 Golf 2 piece lower lip
Rear window venetian blind
Towbar installed (for rear extra chassis rigidity)
Vinyl black "corolla" pin-striping
*Paint is a bit rough, but presents ok.

INTERIOR:
Factory Tacho Dash (modified to work with current coil set up)
Blue material, well maintained.
Twin Cam Steering Wheel
Recaro driver seat - Retrimmed, with all new genuine Recaro foams installed on factory Recaro/Toyota Runner!
*Has speakers installed into front doors on beige mounting base, looks a bit out of place?
CD/USB Player

ENGINE:
St 20V in RWD format
Open quads fitted with bell mouth trumpets, ITG filter socks and internal springs
Sard adjustable FPR
T2 Alloy lightweight crank pulley and water pump under drive pulley
Laser cut alloy "Idle speed control valve deletion plate" installed to top of ITB.
All ITB hoses replaced with blue silicon with use of a vacuum block - cleaned up the factory rats nest.
Dizzy blank plate
Thermostat bypass plate
Rear waterpipe block
RWD 4A engine mounts
Wrapped Stainless steel 4-1 header
Microtech ECU and Dash unit with wiring full loom to suit St20V
Cusco Strut brace
AE71 Alloy radiator mounted laser cut brackets with rubber mounting grommets.
16" Toyota Denso radiator mounted to rad on stainless steel brackets.
Internal regulator alternator wiring mod
Speedflow fittings used where possible
Brand new oil filter and oil installed.

DRIVETRAIN:
Clutch master cyl - fire wall mod / hole
AE71 Pedal Box with brand new T18 master cylinder
Blue braided clutch line - master to slave
Brand new slave cyl
W56 with A-Z customs T50 Bell adapter – shifter hole requires no cutting at all on manual or auto xE7x, perfect position
JDM T50 bell (Clutch fork on Driver side)
ST Flywheel (212mm)
Exceddy 4 puck solid brass button clutch
Tailshaft to suit W series / BW Diff

Comes with S2 T18 diff with stock T18 tailshaft included, needs front yoke changed to suit w series box.

SUSPENSION:
Lowered springs, falcon chopped rears
New AJPS motorsport Tie rods
New AJPS rack spacer
New AJPS poly rack bushes
Sigma Control arms with modded bushes to suit AE71 Xmember
Brand new ball joints installed.

WHEELS:
5 x CSX/DXX Alloy's - BF Goodrich tyres with very good tread.

Rego until December
No mod plate for conversion or Recaro seat.
There really is not an issue with getting this done, I just haven't been stuffed to do it.
The Recaro seat is mounted on a factory Recaro/Toyota Surf rail that has been tweaked to make it fit.
No cutting, welding or extra holes were required to install, and it picks up on the factory xE7x mounting points.
The engine xmember is a factory AE71 4A item, as are the engine mounts and pedal box used.
The W series gearbox mount is custom, and has been done professionally.
Exhaust after extractor is bit average.

I am not in a rush to sell.
EOI for now
0449 838 779
Ali

Pictures taken 02/06/2015.
Engine bay pictures will follow soon

[Futo_gt86]

[AJPS]

looks good mate

hope it goes to a good home

[Futo_gt86]

I appreciate that Dave, thanks man!

This is only advertised on AE86DC, yall get first dibs.
I really don't want to split it up, but if it does come to that, I'll post up in here first.

Ali

[Futo_gt86]

Updated photos.

[Futo_gt86]

Still available.

[Futo_gt86]

No Longer for sale!

[gw]

I saw this on the back of a truck in Broadbeach this morning. How many kms on the 20v?

[Futo_gt86]

Unknown Kms on the ST, when I cracked the valve cover open, its was nice and gold inside.
Compression showed 190 190 185 190
leak down showed 1,2 and 4 equal, no.3 had slight intake valve leak, was 5% but all in spec.

Its been sold, that was the tilt tray taken her to new owners.

Ali