Results 1 to 5 of 5

Thread: AE86 4AC converson to 4AGE

  1. #1
    Junior Member
    Join Date
    Feb 2017
    Name
    Mitch
    State
    Victoria
    Location
    Melbourne
    Country
    Australia
    Posts
    1

    Default AE86 4AC conversion to 4AGE

    Hi Guys,

    I am looking at purchasing a 1983 AE86 with a stock 4AC. I am highly interested to put a 4AGE in. I have heard that the swap just involves engine, wiring loom and ECU. The rest is supposedly universal such as gearbox, starter motor, engine mounts etc. Any advice on this topic would be highly appreciated.

    Thanks.

    Mitch.
    Last edited by mitchgoring; 22nd February 2017 at 12:41 PM.

  2. #2
    Senior Member Slimer86's Avatar
    Join Date
    Dec 2008
    Name
    Marco
    State
    SA
    Location
    North Adelaide Suburbs
    Country
    Australia
    Posts
    775

    Default

    My advice, search.
    Here, toymods,club4ag,rollaclub,twincam.org
    Big up's for the North East Massiv'
    NSATB - New Skids Around The Block

  3. #3
    Senior Member cbjaust's Avatar
    Join Date
    May 2009
    Name
    Chris
    State
    VIC
    Location
    Melbourne
    Country
    Australia
    Posts
    256

    Default

    things to consider:
    bell housing to get the slave cylinder on the driver's side away from the exhaust
    accessory drive pulleys - 4A-GE has ribbed type, need alternator and A/C compressor pulleys to match crank pulley
    flywheel 8-bolt for 4A-GE vs 6-bolt for 4A-C

  4. #4
    Member
    Join Date
    Jan 2015
    Name
    Dave
    State
    Michigan
    Location
    South Lyon
    Country
    USA
    Posts
    65

    Default

    You also need to mod the fuel system for the higher injection pressure and return line. Dave W

  5. #5
    Noooob
    Join Date
    Jun 2010
    Name
    Matt
    State
    NSW
    Location
    Campbelltown
    Country
    Australia
    Posts
    5,246

    Default

    Its well worth the time to do it.. If you buy a jap conversion the the clutch is moved, but you can shield it from the exhaust / run a sleave.

    It's been covered heaps of times, but a summarised version of this swap is.

    * Remove old motor / box.
    * Remove remote voltage reg for alternator
    * Bolt 4age up to t50, if using FWD don't forget the spigot bearing in the crank
    * Add heat shield to clutch near exhaust
    * Sort out fuel system ( AJPS do a neat solution with their surge tanks)
    * Install motor
    * Modify the exhaust
    * Wire up and drive
    Ae86 Drivingclub - Toyota AE86 Car Club where AE86 | KE70 | Toyota 86 / GT86 | Subaru BRZ | Scion FRS owners

Similar Threads

  1. Replies: 7
    Last Post: 30th April 2014, 12:43 AM
  2. QLD Sunny Coast - AE86 4age exhaust may suit 4age keto
    By JDMBenji in forum Car Parts For Sale
    Replies: 3
    Last Post: 14th April 2013, 08:39 PM
  3. Replies: 2
    Last Post: 2nd September 2012, 08:44 PM
  4. 20V RWD Converson - Bottom Radiator Hose?
    By Futo_gt86 in forum Technical - Questions
    Replies: 15
    Last Post: 25th October 2011, 12:46 AM
  5. (vic)- ae86 / ae71 / ke70 .... manual converson complete set.
    By ghettorolla in forum Car Parts For Sale
    Replies: 5
    Last Post: 17th August 2011, 03:35 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •