Results 1 to 6 of 6

Thread: Idle control 20v

  1. #1
    Senior Member
    Join Date
    Jun 2011
    Name
    bazz
    State
    nsw
    Location
    sydney
    Country
    australia
    Posts
    216

    Default Idle control 20v

    Hi all trying to adjust the setting for a st 20v using an old haltech (BAC)
    Anyone have anyone know the frequency? Or settings?
    Cheers

  2. #2
    Noooob
    Join Date
    Jun 2010
    Name
    Matt
    State
    NSW
    Location
    Campbelltown
    Country
    Australia
    Posts
    5,246

    Default

    What model haltech are you running, i know the sprint 500's can't control the idle stepper motor properly.

    If you give haltech a call, they'll support you on the phone, every ecu sold comes with support.
    Ae86 Drivingclub - Toyota AE86 Car Club where AE86 | KE70 | Toyota 86 / GT86 | Subaru BRZ | Scion FRS owners

  3. #3
    Senior Member
    Join Date
    Jun 2011
    Name
    bazz
    State
    nsw
    Location
    sydney
    Country
    australia
    Posts
    216

    Default

    It’s an older e8. Last time I sent them an email they pretty much said that it’s a prehistoric ecu and they don’t make parts etc anymore. Don’t think they’ll be much help.
    The guy who had the setup wasn’t running it. So I’ve added it to the build.

  4. #4
    Senior Member Hen may possibly be a nut's Avatar
    Join Date
    Jan 2009
    Name
    Hen
    State
    Victoria
    Location
    Mt Macedon
    Country
    Australia
    Posts
    909

    Default

    Is the 20V ISCV like the ZE? Three pin, with 12V in the middle and an "open" wire and a "close" wire?

    If so then I have a diagram for a circuit that will convert a single PWM wire into two signals for the "open" and "close" wire. I may even be able to dig out the parameters I used to control the ZE idle.

  5. #5
    Senior Member
    Join Date
    Jun 2011
    Name
    bazz
    State
    nsw
    Location
    sydney
    Country
    australia
    Posts
    216

    Default

    Yeah that’s correct. Low 12v and high. I’ve wired it in with 2 pwr and a 12v. It’s just the frequency and settings I’d be really greatful for

  6. #6
    Senior Member Hen may possibly be a nut's Avatar
    Join Date
    Jan 2009
    Name
    Hen
    State
    Victoria
    Location
    Mt Macedon
    Country
    Australia
    Posts
    909

    Default

    Just dug out some old maps (from Wolf 3D V4). Not really sure it'll help. The frequency I have set to 150. But I think that may not be in a useful unit, but just a value between 0 and 255. In any case, you can just try varying the frequency until the buzzing isn't annoying, and the valve still works as desired.

    None of the other parameters I have seem to match what the Haltech requires. So not much more help from me I'm afraid. However, looking at the parameters it shouldn't be too hard to get it up and running. Ignore the post-start and aircon initially. And just play with the others one at a time til you understand how they work and can get a good combination. Also remember that you have a "dumb" air bypass screw I assume too, which lets you set the base idle, then the ISCV adjusts from this start point.

Similar Threads

  1. 1G-GTE Idle speed control valve
    By CraigMX73 in forum Cars or Parts Wanted
    Replies: 0
    Last Post: 25th September 2014, 12:23 AM
  2. WTB: idle control valve smallport 4ag
    By wt86 in forum Cars or Parts Wanted
    Replies: 0
    Last Post: 1st November 2013, 09:19 AM
  3. WTB: aw11 gze idle control valve
    By mistr2 in forum Cars or Parts Wanted
    Replies: 3
    Last Post: 22nd January 2009, 06:54 PM
  4. 4age idle control motor
    By lewy in forum Cars or Parts Wanted
    Replies: 1
    Last Post: 11th March 2007, 08:37 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •