Page 1 of 2 1 2 LastLast
Results 1 to 10 of 15

Thread: R32 non ABS Master cylinder

  1. #1
    Senior Member DRFTR86's Avatar
    Join Date
    Dec 2008
    Name
    Richard
    State
    VIC
    Location
    South Oakleigh
    Country
    Australia
    Posts
    783

    Default R32 non ABS Master cylinder

    Car - ae86

    motor - ca18det

    use - skids

    problem - R32 non abs master cylinder

    how are the lines setup, there is 4 outlets how are the lines meant to go when installed in a 86/ke70???

    any pics of peoples installs??

    PROTEK TYRE AND AUTO
    SQ ENGINEERING
    NCCE

    DRFTR86 & FATKE.....DOSEING COROLLAS SINCE 2009

  2. #2
    Senior Member Oly AE86's Avatar
    Join Date
    Dec 2008
    Name
    Oliver
    State
    QLD
    Location
    Logan Shire
    Country
    Australia
    Posts
    357

    Default



    This is R32 non-abs that I used. Don't know what you have with 4 outlets.......

    On the left R is for the rear brakes, other two marked F go to the fronts.

    I removed the original proportional valve.
    I then bent the passenger side front line to reach the newmaster cylinder.
    I then bent the rear single line to match up with new master cylinder.
    I then used the line from the OLD master cylinder to OLD old proportional valve as the NEW line for the Drivers side front, with some bending, shortening and a re-flare on one end.

    The setup didn't require any new lines, just some fiddling, careful bending and a re-flare of one end.

    Sorry I don't have any installed pics showing detail, its mostly covered by intake plenum.
    Last edited by Oly AE86; 21st August 2009 at 09:20 PM.

  3. #3
    Senior Member
    Join Date
    Jan 2009
    Name
    Mark
    State
    TAS
    Location
    Hobart
    Country
    Australia
    Posts
    783

    Default

    hey.
    Did you use any proportioning valve at all? How does it feel? Reckon people thinking of doing rx7 brakes with r32 master should use one?
    Launceston = Home of the surprise sodomist!!

  4. #4
    Senior Member
    Join Date
    Dec 2008
    Name
    Reeece
    State
    NSW
    Location
    Casula
    Country
    Australia
    Posts
    688

    Default

    I dont get how your not using prop valve? does your braking work ok?

  5. #5
    Senior Member dave2221's Avatar
    Join Date
    Dec 2008
    Name
    David
    State
    NSW
    Location
    Sydney
    Country
    Australia
    Posts
    819

    Default

    i am halfway through this. I am going to blank off one of the front valves and keep the stock proportioning valve

  6. #6
    Senior Member fatke's Avatar
    Join Date
    Jan 2009
    Name
    Daniel
    State
    VIC
    Location
    Oakleigh South
    Country
    Australia
    Posts
    251

    Default

    im not using a proportioning vavle, all i did was bent the lines with drfter 86 and made it fit on the r32 master
    CATCH MY DRIFT
    SQ ENGINEERING
    PROTEK
    NCCE ( Naths crazy corolla electrics )



    FATKE & DRFTR86....DOSEING COROLLAS SINCE 2009

  7. #7
    Elite rthy's Avatar
    Join Date
    Dec 2008
    Name
    Leo
    State
    VIC
    Location
    Tulla
    Country
    Australia
    Posts
    7,305

    Default

    prop valve is built into it the r32 mc

    4 outlet is for 2 front and 2 rear
    3 outlet is for 2 front and 1 rear
    30kw club

  8. #8
    Senior Member Oly AE86's Avatar
    Join Date
    Dec 2008
    Name
    Oliver
    State
    QLD
    Location
    Logan Shire
    Country
    Australia
    Posts
    357

    Default

    Rthy is on the money, has proportioning system built in.

    I have RX7 4 Piston fronts and T-18 Drums on the rear, proportioning feels fine and when getting certification plates the tester was impressed by the breaking performance
    Last edited by Oly AE86; 22nd August 2009 at 08:06 PM.

  9. #9
    Senior Member Dazzla86's Avatar
    Join Date
    Jan 2009
    Name
    Darren
    State
    WA
    Location
    Leeming
    Country
    Australia
    Posts
    481

    Default

    and it bolts straight onto the original studs???

  10. #10
    Veteran Skylar's Avatar
    Join Date
    Mar 2009
    Name
    Ken
    State
    WA
    Location
    Perth
    Country
    Australia
    Posts
    1,370

    Default

    yessum.

Page 1 of 2 1 2 LastLast

Similar Threads

  1. WTB... BM44 non abs Master.
    By --Redwork-- in forum Cars or Parts Wanted
    Replies: 4
    Last Post: 6th September 2010, 05:31 PM
  2. part number for R32 non abs brake master
    By Mr Awsome in forum Technical - Questions
    Replies: 3
    Last Post: 13th November 2009, 09:21 PM
  3. WTB: R32 non abs brake master
    By Mr Awsome in forum Cars or Parts Wanted
    Replies: 2
    Last Post: 1st November 2009, 01:39 PM
  4. wtb : R32 master cylinder
    By evil86 in forum Cars or Parts Wanted
    Replies: 1
    Last Post: 21st February 2009, 12:56 PM
  5. WTB: R32 Non ABS brake master cylinder
    By Sparkle86 in forum Cars or Parts Wanted
    Replies: 2
    Last Post: 20th November 2007, 11:17 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •