psi20v needs to go! BLOWN MOTOR. cheap, will consider parting out

[ae71 kid]

as title says its got a blown motor now but the add below was from before.

engine has a cracked piston i beleive, not confirmed but thats what it seems like,

engine:
silver top 20v
acl race bearings
fully balanced
arias forged pistons with moly race rings (approx 9.0:1 comp)
freshened head
0.8mm metal head gaskit
sump to rocker cover, no hang ons
$500

spare engine in peices so call if u need bits like 20v block, head, crank, pistons, sump etc

3 inch full exh from turbo back with 1 straight through muffler and side exit
$200

pod filter

custom cooler piping with progressive smooth pipesize changes and tridon t-bolt clamps
3 inch in and out e-bay frontmount cooler
turbosmart supersonic bov
$200


microtec ecu with hand controller mounted on dash
loon to suit ke and 20v
bosch coilpacks and top gun leads
comes with the 230kw map
$1000

cooling system:
custom home designed and made rwd water kit including water pump and backing, rear blanking plate with heater outlet fitting and side blanking plate with coolant temp sensor. also all hoses.
$250

s-13 turbo radiator with twin wrx thermos
offers

v8 merc trans cooler used as oil cooler mounted ontop of intercooler
remote oil filter kit including sandwich plate for temp and pressure guages
and oil lines
$200

fuel system:
custom surge tank
vl intank lift pump
bosch 044 high pressure pump
8mm fuel lines
$300

std 20v flywheel
offers

w55 gearbox
$300

corona tailshaft shortened & modded to suit ke/ae wit r31 diff
$100

r31 skyline diff
standard width
ke mounts welded on
4.11:1 ratio minispool centre
$800

fnt suspension/brakes:
sold

rear:
falcon springs
swaybar from front of e 36 bmw
torana kyb excel G's.
$200

custom hydraulic handbrake
sold

body:
typical matt black drifter
few dents
bog here and there
overall it looks great if u ask me, but rought if your picky
large flared guards for wheel clearance
front inner guards massaged for clearance
rough hole in bonnet for old wastegate setup
modified wrx front bar (currently not fitted)
bonnet pins
solex locks
manual pedalbox
4a x member
2X sets of 4a engine mount brackets
:offers on all

15x8 -4 performance superlites in white:
1 set with toyo proxes R1R's 195/50/15 60%: 500
1 set with hero milanza 195/50/15s 60-70%: 400
1 set with hero milanza 195/50/15s BALD : 360

interiour & miscelanious
autobarn bucket driver seat
$100

r32 skyline passenger seat
$100

otherwise stripped(can get rear seats if required)


small saas steering wheel
$80

4 point harness not fitted
$50

oil temp, oil pressure guages
$40 each

random adjustable strut bar (requires custom made mounts)
$60

ive prolly forgotten some shit but thats about it, please only post if your interested or if you have positive comments

car is located in croydon nth.

pics will be up soon, i can sms pics right now so msg me if u want pics asap

reg ran out in dec but if its payed within 3 months it doesnt need to go to vic roads.

0402 686 057

thanks tim

[sleeperketo70]

if u end up parting it out im intrested in full turbo setup for my n/a 20v or a price for the motor with it and also the cage.
cheers

[blair]

body:
typical matt black drifter



sorry, but i just lol'd really hard!

gl with the sale mate

[FMP086]

interested in gearbox and diff if u part it out

[ae71 kid]

edited first post with prices!! its getting parted out so come grab what u want guys get in quick!! most prices are slightly negotiable.

cheers tim

[shift_rook]

sucks to hear man, when did you do that? what are you getting next?

[Nic19]

Pics of hydro handbrake.

[Cerby86]

I might be keen on the steering arms if you would seperate. Price?

[ae71 kid]

pics of some stuff here, more to come after camera is charged!

[ae71 kid]

here they are

[ae71 kid]

I might be keen on the steering arms if you would seperate. Price?

if u get me some stock ones mate ill just mod em for ya!!

[Drift_Donkey]

what brand is the harness and how much?

[shelldrake]

keen on the bellhousing and it's accessories if not already spoken for. msg sent...

[ae71 kid]

handbrake, cage & possibly oil cooler and filter setup sold pending payment.

also have 4a x member once engine is sold, manual pedalbox and clutch master, clutch line etc spare 20v botom end incl rods pistons etc and incomplete head, cams, cam cover plug cover etc

[ae71 kid]

what brand is the harness and how much?

its an old saas 4 point item, ill take $60 for it

[ae71 kid]

bumpety

[ae85 trueno]

price on wheels ?

[ae71 kid]

2x good ones with toyo r1r at 65% or so = $550

2x good ones with 75% heros = $400

2x one is damaged round the outer lip due to tyre failure during a high speed entry but looks fine if u ask me, shaged heros. = $360

[ae71 kid]

bellhousing sold!
clutch, flywheel and w55 gearboxes still available along with most other parts!!

[KENut]

How much use have the front coilovers seen? And could you get some pictures to show the general condition of them please? Cheers

[ae71 kid]

they are near new mate, car has done less than 2000km on this motor and they were installed after that... ill get some snaps mate. pm u

[ae71 kid]

camera charge cable is lost mate... just come look, guarunteed not to be dissapointed...

[KENut]

T'would be a trek just for a look, I'm near the ACT haha.
I'm willing to wait for pictures, am pretty keen on coilovers.
Also, how much were the struts shortened?

[ae71 kid]

ha ha fair enough! i did it all myself but i am a little foggy on the details, i believe they are 40mm shorter but can measure to confirm if u have standard length specs to compare! ill borrow my bros camera and get u those pics, u wanting them as package incl (brakes, steering arms and lca's) or just coilovers

[KENut]

Yeah mate, as a package with brakes etc. I think stock corona struts are around 405mm. I can measure some KE70 ones, which are probably the same height

[ae71 kid]

ok these are the best i could do with the light and the camera available, doesnt really give the best ide of how fresh they are but they are!
see pads are near new and rotors are score free and new looking, this whole setup was done at the same time so u can see by condition of the brakes that it hasnt done much work at all...
what u reckon

[sly1]

ill take the fuel system set up....pm me

[Hazzard]

any pics of the shell?

[ae71 kid]

sly1 i have pmed u

hazzard i have no pis of the shell yet sorry, whats ur intended use for it?

[Hazzard]

might be interested in a few things.... and pics help things sell. Ya wouldnt happen to have a 4a X member, T50 X member, ae71 pedal box would ya? and how much for the shell? just for ppl interested.

Hazzard

[ae71 kid]

havnt thought about how much for the shell yet, was gonna deal with that once all the stuff is sold out of it!
i have plenty of pics of all the stuff worth photographing like custom stuff jus didnt wanna jam the thread with thousands of pics, if ppl are interested in particular things then ill pm or post pics.
i have 4a x member and manual pedal assembly! no t-50 x member

[Hazzard]

how much were ya after for the pedal box and X member?

Hazzard

[ae71 kid]

300 for the lot incl clutch master and metal line to slave (slave not incl)

[ae71 kid]

bump.........

[ae71 kid]

updated first post incl sold items and price drops! make some offers guys... need it gone!

[Skid_KE70]

hey dude, sorry to hear about the engine. im interested in your clutch and bellhousing if u still have it? pm me a price thanks dude.

im the guy with the green 20v turbs ke in tas

[ae71 kid]

nah thats sold man, sorry. have u already blown the t-50?

[Skid_KE70]

3 to be exact

[Nic19]

hey tim sorry to be off topic, but did u try an auto xmember and mount wen u did the w5x conversion?

[Adsport]

do you still have the engine mount brackets? i seem to have snapped one of mine *shrug*

[ae71 kid]

nic, no i didnt try anything else! jus modded mine!

do u still need the mounts adsport? i have 2 sets!