AE86 itb plenum/chamber

[BlueLevin]

Hey guys
Running itbs on my 16v, don't want to run sock filters
So can anyone recommend a certain chamber/plenum, anyone with experience with them? and where to acquire said plenum :)
Thanks!!

[LittleRedSpirit]

Noby Booth. Geenline or Nengun.

Not many other options readily available unless you use something like a pipercross filter chamber, which is quite good, but hard to control air temps with.

[Sam-Q]

this is what I offer

http://www.ae86drivingclub.com.au/dcimages/2/5/2/313598.jpg

http://www.ae86drivingclub.com.au/dcimages/2/5/2/313599.jpg

[BlueLevin]

That actually looks somewhat standard! But I'm running an NA so would the lack of rams loose a little power?

[Sam-Q]

because of the internal radii not so much. I had one guy report a slight loss from open trumpets and from using sock filters probably a gain in power.

[BlueLevin]

Have you got any pictures of fitment in ae 86 engine bay? And how much are you after for one?
Thanks Sam!

[Futo_gt86]

Picture of it fitted in 86 engine bay, scroll down
http://www.ae86drivingclub.com.au/forums/showthread.php/25870-Using-a-nissan-GTIR-intake-on-a-20V/page9?highlight=GTiR
The whole thread is a decent read!

[Sam-Q]

$250 for the adapter plate inc bolts and new gasket

[DR86FT]

25395

[Sam-Q]

looks nice

[DR86FT]

Thanks Sam will it miss the heater tap and and clutch master?

[LittleRedSpirit]

Looks like it misses everything by miles.

[Sam-Q]

Thanks Sam will it miss the heater tap and and clutch master?

clutch master easy however for the heater tap I took out one of the two rubber isulators and then it was ok on a little bit of an angle. I am also running a 10mm gearbox spacer.

[ae86 slide]

Do you do a package that includes the plenum, throttle body's, gaskets etc pretty much everything needed?

[Sam-Q]

I have made a thread in my sponsor section instead of using this as a sales thread which isn't right

http://www.ae86drivingclub.com.au/forums/showthread.php/70326-Nissan-GTiR-adapter-plates?p=869657#post869657

[takai]

Maybe try something a little larger?
http://www.ae86drivingclub.com.au/dcimages/522135.jpg

[Sam-Q]

I like my brake booster

[BlueLevin]

Looking for something similar for that, too worried that the gtir set up is too small for NA, but also of corse want my booster :)
The nobby booth one looks like it would be very close, but can buy it without holes cut and comes with template to cut them.
But still scrounging around for more options

[takai]

GTIR setup will be fine for any road going NA engine.

Heck it would probably be fine for almost all NA engines. Only a limited few have engines which would require more.

[BlueLevin]

Will have 272 or higher, not sure on lift cams, ported smallport head, 11.3-11.6 - 1 compression (pistons) and a fairly free flowing exhaust, curly extractors and what not. Not sure if it warrants bigger plenum or not but don't want to have less than my engine needs. Car will be used for daily/hillclimb and some fun days at winton and stuff so if having a bigger plenum will give me a little more at the wheels then I'll go down that road, better to have more air and not need it then need it and not have it I guess

[takai]

Will be fine, absolutely fine.

You might need bigger when you are running 318deg cams, 13.5:1 CR and spinning to 9800rpm. Or in the case of the engine above a 1.9L 7AG to 8800rpm.

[BlueLevin]

Good to know, gives me alot more choices!!! Thanks for the info guys
Now all I have to choose is what ever is aesthetically pleasing for me~
thanks again for all the responses

[LittleRedSpirit]

http://www.sbdev.co.uk/Air_Filters/Air_Boxes_Backing_Plates/Air_Boxes_Backing_Plates.htm

seen this?

There's one on ebay right now.

http://www.ebay.com/itm/SBD-type-induction-airbox-for-jenvey-tbs-weber-45s-race-rally-autograss-C20XE-/140765136360?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item20c64185e8

Wonder how it would fit?... That notch might be handy at the back.

[LittleRedSpirit]

Or there is this site:
http://www.reverie.ltd.uk/
Some amazing gear there and some that would likely fit.

Also Jenvey... (http://www.jenvey.co.uk/home/accessories/airhorns-filters-and-boxes)

[NIZLAH]

Nice find Matt, a few of those look promising

[LittleRedSpirit]

Been doing a lot of looking for chambers lately for the 2az build.

[NIZLAH]

I see I see, the big thing is trying to pick/find the right one that clears everything without having to outlay on something that may or may not fit (clearance wise) always a gamble I guess

[Dylan]

http://www.pipercross.net/competition/products_600_airbox.asp

http://www.pipercross.net/competition/products_px600.asp

Some other options

[tc-rolla]

Any one know what the clearance is like on the 71's with the noby booth setup?