Jordain
6th January 2013, 12:50 PM
Hey got a few motors/parts that are taking up way to much space in my garage.
1) I've got a complete 4age smallport. Has RWD water setup on it, Cut and shut manifold, Clutch, lightened flywheel, ARP flywheel bolts, bigport cams, has good compression on all cylinders. It did blow a little bit of smoke on cold start but went away once driving. The head was reconditioned a few months ago.
$1500
http://www.ae86drivingclub.com.au/dcimages/5/7/1/3/503301.jpg
2) I've got another smallport, this one I built. It's a smallport block, Blacktop crank, rods, pistons. Got new bearings, ring's, acid dipped block, all parts where cleaned, the head was shaved. Compression is 11:5:1. has bigport cams in it. This motor is a long motor has no bolt on parts. It needs big end bearings as I think it's spun a bearing.. either way it's got a light knock on startup and when you rev it hard. Needs rebuilding...
$1000
http://www.ae86drivingclub.com.au/dcimages/5/7/1/3/503302.jpg
3) 7MGTE i bought for my soarer about 10 year's ago. Paid around $2k from ichibarn but .... it's since had parts stolen of it etc.. It did run... no idea if it still does... $200 come take it away... worth $100 in metal lol.
http://www.ae86drivingclub.com.au/dcimages/5/7/1/3/503303.jpg
4) ADAPTRONIC E420c, Blacktop ITBS, T3 adaptor, 70mm trumpets, Vacuum block, Injectors, rail, regulator, FULL custom loom to plug into standard ae86 body loom, or I've labeled it to be easily wired into any car. Theres 4 wires to connect.
$1300
http://www.ae86drivingclub.com.au/dcimages/5/7/1/3/503304.jpg
Jordan - 0468403713
1) I've got a complete 4age smallport. Has RWD water setup on it, Cut and shut manifold, Clutch, lightened flywheel, ARP flywheel bolts, bigport cams, has good compression on all cylinders. It did blow a little bit of smoke on cold start but went away once driving. The head was reconditioned a few months ago.
$1500
http://www.ae86drivingclub.com.au/dcimages/5/7/1/3/503301.jpg
2) I've got another smallport, this one I built. It's a smallport block, Blacktop crank, rods, pistons. Got new bearings, ring's, acid dipped block, all parts where cleaned, the head was shaved. Compression is 11:5:1. has bigport cams in it. This motor is a long motor has no bolt on parts. It needs big end bearings as I think it's spun a bearing.. either way it's got a light knock on startup and when you rev it hard. Needs rebuilding...
$1000
http://www.ae86drivingclub.com.au/dcimages/5/7/1/3/503302.jpg
3) 7MGTE i bought for my soarer about 10 year's ago. Paid around $2k from ichibarn but .... it's since had parts stolen of it etc.. It did run... no idea if it still does... $200 come take it away... worth $100 in metal lol.
http://www.ae86drivingclub.com.au/dcimages/5/7/1/3/503303.jpg
4) ADAPTRONIC E420c, Blacktop ITBS, T3 adaptor, 70mm trumpets, Vacuum block, Injectors, rail, regulator, FULL custom loom to plug into standard ae86 body loom, or I've labeled it to be easily wired into any car. Theres 4 wires to connect.
$1300
http://www.ae86drivingclub.com.au/dcimages/5/7/1/3/503304.jpg
Jordan - 0468403713