Page 1 of 2 1 2 LastLast
Results 1 to 10 of 15

Thread: AE86 Shell, Tomei stroked ca18 package

  1. #1
    Veteran johl's Avatar
    Join Date
    Dec 2008
    Name
    Johl
    State
    QLD
    Location
    Brisbane
    Country
    Australia
    Posts
    2,812

    Default AE86 Shell, Tomei stroked ca18 package

    I am parting out my 86 i have been building since 08. first i am selling the shell and engine once that is gone i will put up a new thread with everything else.

    located near ipswich QLD
    pm me on here or just reply to thread and i will send you my phone number

    shell sold


    tomei stroked ca18 (2litre)
    CA18DET bored and stroked to 2L using Tomei Stroker kit (pistons, crankshaft, tomei piston rings)
    Re-Bored and Milled block
    Bored oil drain backs
    Resized conrods
    Linished crankshaft
    MLS metal Head gasket
    Rebuilt and match ported head
    ARP conrod, head and flywheel bolts
    Gates race timing belt
    New water pump
    Race bearings
    Port matched inlet manifold with butterflies removed and SR20DE throttle
    S4 RX7 injectors (550cc)
    Nismo fuel pressure regulator
    HKS oil cooler kit
    Greddy FMIC with stainless piping
    Splitfire coilpacks
    HKS 264 degree 8.5mm lift cams
    Extended and baffled sump
    Adaptronic ECU and new engine loom
    npc 5 puck button clutch

    since i bought the engine from my mate who had it in a red s13 which alot of people knew, i put a brand new core in the t517z turbo which cost $950.

    engine has been tuned to 270hp on an adaptronic and the engine wiring is custom.
    done less than 10 000km





    PRICES-

    SHELL- sold
    ENGINE, GEARBOX, EVERYTHING $5000

    ***prices are negotiable but i will not talk money over pm or text message unless you are interstate and i think you are a genuine buyer. i am happy to include other things from the car if you are purchasing the engine or shell and i'l look after you with prices. ***

    build thread-
    Last edited by johl; 10th February 2013 at 10:13 PM.
    stroked 2L ca18-ae86 in the build...eta xmas 2012?

  2. #2
    Senior Member killabeez_1985's Avatar
    Join Date
    Apr 2010
    Name
    Adam
    State
    QLD
    Location
    Mount Gravatt
    Country
    Australia
    Posts
    321

    Default

    PM'd about shell

  3. #3
    Veteran johl's Avatar
    Join Date
    Dec 2008
    Name
    Johl
    State
    QLD
    Location
    Brisbane
    Country
    Australia
    Posts
    2,812

    Default

    shell price reduced to $2300 ono
    stroked 2L ca18-ae86 in the build...eta xmas 2012?

  4. #4
    Senior Member
    Join Date
    Jan 2009
    Name
    Paul
    State
    NSW
    Location
    Sydney
    Country
    Australia
    Posts
    266

    Default

    Johl can you pm me your number to talk about the shell. looks like it will be cheaper than doing mine up depending on how complete it is.

    Cheers
    Paul

  5. #5
    Senior Member ae86 slide's Avatar
    Join Date
    Jan 2009
    Name
    Jason
    State
    NSW
    Location
    Gold Coast
    Country
    Australia
    Posts
    788

    Default

    Dude! What happened?
    But, if you're serious about this I'm keen on the strut brace you got off Seamus. When the time comes. If it comes (I hope not for your sake).
    Make sure you double think this decision man.

  6. #6
    Member Powerbite's Avatar
    Join Date
    Nov 2011
    Name
    James
    State
    Tasmania
    Location
    Launceston
    Country
    Australia
    Posts
    50

    Default

    I'd take the rear coils is you decide you want to sell just those

  7. #7
    Veteran johl's Avatar
    Join Date
    Dec 2008
    Name
    Johl
    State
    QLD
    Location
    Brisbane
    Country
    Australia
    Posts
    2,812

    Default

    pm sent paul.

    yeh jase i was at the point where money spent on custom wiring and tuning would be thrown away if i was to sell later, and with me wanting to build a house i did the numbers for how much it will cost to take it to the track for a weekend and i was looking at atleast $500 if i didnt break anything. with a $400 000+ mortgage i just couldnt justify it.

    james- i'l keep that in mind but they are going to be near impossible to remove from my diff due to the bush being such a tight fit when i put it on
    stroked 2L ca18-ae86 in the build...eta xmas 2012?

  8. #8
    Member Powerbite's Avatar
    Join Date
    Nov 2011
    Name
    James
    State
    Tasmania
    Location
    Launceston
    Country
    Australia
    Posts
    50

    Default

    Alright cheers man, keep me updated

  9. #9
    Senior Member ae86 slide's Avatar
    Join Date
    Jan 2009
    Name
    Jason
    State
    NSW
    Location
    Gold Coast
    Country
    Australia
    Posts
    788

    Default

    Yeah Johl I hear ya mate. It's a constant battle between track days and a mortgage for me. Grown up life sucks

  10. #10
    Senior Member Vaughn's Avatar
    Join Date
    Jun 2010
    Name
    Vaughn
    State
    QLD
    Location
    Sunshine Coast
    Country
    Australia
    Posts
    306

    Default

    Johl, This is sold isnt it?
    Just another Muppet

Page 1 of 2 1 2 LastLast

Similar Threads

  1. [SA] ADM AE86, 4AGZE, Tomei 2way, RX7 4 pots, Half Cage etc...
    By s3phro in forum Cars for Sale (Toyota Only)
    Replies: 6
    Last Post: 23rd May 2012, 06:37 PM
  2. Replies: 0
    Last Post: 17th May 2012, 11:48 AM
  3. [SA][EOI] ADM AE86, 4AGZE, Tomei 2way, RX7 4 pots, Half Cage etc...
    By s3phro in forum Cars for Sale (Toyota Only)
    Replies: 11
    Last Post: 25th March 2012, 02:55 PM
  4. sr20 parts and package s13 rolling shell microtek computer
    By bencozzy in forum Car Parts For Sale
    Replies: 0
    Last Post: 28th July 2010, 04:20 PM
  5. ca18 ae86
    By johl in forum General Topics (No Technical Questions)
    Replies: 6
    Last Post: 6th June 2005, 04:06 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •