Page 10 of 18 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 LastLast
Results 91 to 100 of 174

Thread: Building a 7age.

  1. #91
    Veteran pen15's Avatar
    Join Date
    Dec 2008
    Name
    Mathew
    State
    NSW
    Location
    Sutho Shire
    Country
    Australia
    Posts
    1,859

    Default

    if this helps people i have pics of sump clearances and other 7a related things

    sump to sway bar


    sump to crossmember


    hope this helps anyone with knowing where the sump sits on a 7age setup
    the dyno pull to 300rwkw

    BT20v is making 300rwkw like i said i would without nitrous so now its time for some spray and see if she will run a 10s or less

  2. #92
    Elite rthy's Avatar
    Join Date
    Dec 2008
    Name
    Leo
    State
    VIC
    Location
    Tulla
    Country
    Australia
    Posts
    7,308

    Default

    re. the headgasket, the 7afe gasket is .6mm and metal but the hole passage for the oil/water are smaller/different design.
    can enlarge the passages but might/will damage or warp the gasket.


    (old 7afe vs new 4age headgasket)
    30kw club

  3. #93
    Senior Member
    Join Date
    Aug 2009
    Name
    Jim
    State
    VIC
    Location
    Wodonga
    Country
    Australia
    Posts
    104

    Default

    From what I have read, depending on head gasket used

    Small port pistons = roughly 11.5:1 CR
    standard 7a pistons will result in less than 9:1 CR
    Late ZE pistons just over 9.5:1 CR

    Has anyone used the 4agelc pistons which are 9.4:1 CR normally in a 4ag motor. I would image they would result in about a 10.5:1 CR

  4. #94
    User fantapants's Avatar
    Join Date
    Dec 2008
    Name
    Pat
    State
    TAS
    Location
    Other
    Country
    Australia
    Posts
    1,635

    Default

    dont forget the compression ratio also depends on if the builder chooses to deck the block down to the piston or not...
    RIP Carly - a smile to light the world.
    06/07/2011

  5. #95
    Senior Member
    Join Date
    Aug 2009
    Name
    Jim
    State
    VIC
    Location
    Wodonga
    Country
    Australia
    Posts
    104

    Default

    Yes I understand that, but with all things being equal, it would be interesting to see what compression ratio that piston gave compared to all the rest.

  6. #96
    Noooob
    Join Date
    Jun 2010
    Name
    Matt
    State
    NSW
    Location
    Campbelltown
    Country
    Australia
    Posts
    5,246

    Default

    Wondering if anyone has used blacktop 20v pistons and a blacktop 20v head in a 7age?

  7. #97
    Ok
    Join Date
    Nov 2008
    Name
    Seamus
    State
    QLD
    Location
    Milton
    Country
    Australia
    Posts
    1,860

    Default

    my setup does
    4AGE & 7AGE Forged Connecting Rods - Lightweight Flywheels - And Much More



    ^ Clicky clicky!

  8. #98
    Senior Member
    Join Date
    Dec 2008
    Name
    Ben
    State
    SA
    Location
    gawler area.
    Country
    Australia
    Posts
    280

    Default

    what power is your 20v 7ag making ?

    what rods are people using so you can make the 7ag rev a BIT higher ?
    hachi roku

  9. #99
    Senior Member s13 james's Avatar
    Join Date
    Aug 2010
    Name
    James
    State
    NSW
    Location
    Sutho Shire
    Country
    Australia
    Posts
    752

    Default

    i will be using spool rods

  10. #100
    Veteran
    Join Date
    Dec 2008
    Name
    John
    State
    TAS
    Location
    Hobart
    Country
    Australia
    Posts
    2,200

    Default

    most people are using spool or 7oxins rods

    although robbo did use standard 7afe with ARP bolts...

Page 10 of 18 FirstFirst 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 LastLast

Similar Threads

  1. Replies: 22
    Last Post: 5th March 2012, 10:33 AM
  2. building need parts..
    By josh.. in forum Cars or Parts Wanted
    Replies: 3
    Last Post: 31st March 2011, 09:55 PM
  3. Building a cage
    By driftke70 in forum Technical - Questions
    Replies: 4
    Last Post: 27th January 2007, 04:16 PM
  4. Building 4age
    By works510 in forum Technical - Questions
    Replies: 33
    Last Post: 6th March 2006, 05:14 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •